PSoC® 3: CY8C34 Family
Data Sheet
Programmable System-on-Chip (PSoC®)
General Description
With its unique array of configurable blocks, PSoC® 3 is a true system level solution providing microcontroller unit (MCU), memory,
analog, and digital peripheral functions in a single chip. The CY8C34 family offers a modern method of signal acquisition, signal
processing, and control with high accuracy, high bandwidth, and high flexibility. Analog capability spans the range from thermocouples
(near DC voltages) to ultrasonic signals. The CY8C34 family can handle dozens of data acquisition channels and analog inputs on
every general-purpose input/output (GPIO) pin. The CY8C34 family isalso a high-performance configurable digital system with some
part numbers including interfaces such as USB, multimaster inter-integrated circuit (I2C), and controller area network (CAN). In
addition to communication interfaces, the CY8C34 family has an easy to configure logic array, flexible routing to all I/O pins, and a
high-performance single cycle 8051 microprocessor core. You can easily create system-level designs using a rich library of prebuilt
components and boolean primitives using PSoC Creator™, a hierarchical schematic design entry tool. The CY8C34 family provides
unparalleled opportunities for analog and digital bill of materials integration while easily accommodating last minute design changes
through simple firmware updates.
Features
Single cycle 8051 CPU core
Library of standard peripherals
DC to 50 MHz operation
Multiply and divide instructions
• 8-, 16-, 24-, and 32-bit timers, counters, and PWMs
• Serial peripheral interface (SPI), universal asynchronous
transmitter receiver (UART), I2C
Flash program memory, up to 64 KB, 100,000 write cycles,
20 years retention, and multiple security features
Up to 8-KB flash error correcting code (ECC) or configuration
storage
• Many others available in catalog
Library of advanced peripherals
• Cyclic redundancy check (CRC)
Up to 8 KB SRAM
• Pseudo random sequence (PRS) generator
• Local interconnect network (LIN) bus 2.0
• Quadrature decoder
Up to 2 KB electrically erasable programmable read-only
memory (EEPROM), 1 M cycles, and 20 years retention
24-channel direct memory access (DMA) with multilayer
AHB[1] bus access
Analog peripherals (1.71 V ≤ VDDA ≤ 5.5 V)
1.024 V±0.9-percent internalvoltage reference across –40 °C
to +85 °C (14 ppm/°C)
Configurable delta-sigma ADC with 8- to12-bit resolution
• Programmable gain stage: ×0.25 to ×16
• 12-bit mode, 192-ksps, 66-dB signal to noise and distortion
ratio (SINAD), ±1-bit INL/DNL
Two 8-bit, 8-Msps IDACs or 1-Msps VDACs
Four comparators with 95-ns response time
Two uncommitted opamps with 25-mA drive capability
Two configurable multifunction analog blocks. Example
configurations are programmable gain amplifier (PGA),
transimpedance amplifier (TIA), mixer, and sample and hold
CapSense support
• Programmable chained descriptors and priorities
• High bandwidth 32-bit transfer support
Low voltage, ultra low-power
Wide operating voltage range: 0.5 V to 5.5 V
Highefficiencyboostregulatorfrom0.5-Vinputthrough1.8-V
to 5.0-V output
0.8 mA at 3 MHz, 1.2 mA at 6 MHz, and 6.6 mA at 50 MHz
Low-power modes including:
• 1-µA sleep mode with real-time clock (RTC) and
low-voltage detect (LVD) interrupt
• 200-nA hibernate mode with RAM retention
Versatile I/O system
28 to 72 I/O (62 GPIOs, eight special input/outputs (SIO),
Programming, debug, and trace
two USBIOs[2]
)
JTAG (4-wire), serial wire debug (SWD) (2-wire), and single
wire viewer (SWV) interfaces
Any GPIO to any digital or analog peripheral routability
LCD direct drive from any GPIO, up to 46×16 segments[2]
CapSense® support from any GPIO[3]
Eight address and one data breakpoint
4-KB instruction trace buffer
1.2-V to 5.5-V I/O interface voltages, up to four domains
Maskable, independent interrupt request (IRQ) on any pin or
port
Schmitt-trigger transistor-transistor logic (TTL) inputs
All GPIOs configurable as open drain high/low,
pull-up/pull-down, High Z, or strong output
Configurable GPIO pin state at power-on reset (POR)
25 mA sink on SIO
Bootloader programming supportable through I2C, SPI,
UART, USB, and other interfaces
Precision, programmable clocking
3- to 24-MHz internal oscillator over full temperature and
voltage range
4- to 25-MHz crystal oscillator for crystal PPM accuracy
Internal PLL clock generation up to 50 MHz
32.768-kHz watch crystal oscillator
Digital peripherals
Low-power internal oscillator at 1, 33, and 100 kHz
16 to 24 programmable logic device (PLD) based universal
digital blocks (UDB)
Temperature and packaging
–40 °C to +85 °C degrees industrial temperature
48-pin SSOP, 48-pin QFN, 68-pin QFN, and 100-pin TQFP
package options
Full CAN 2.0b 16-receive (Rx), 8-transmit (Tx) buffers[2]
Full-speed (FS) USB 2.0 12 Mbps using internal oscillator[2]
Up to four 16-bit configurable timer, counter, and PWM blocks
Notes
1. AHB – AMBA (advanced microcontroller bus architecture) high-performance bus, an ARM data transfer bus
2. This feature on select devices only. See Ordering Information on page 115 for details.
3. GPIOs with opamp outputs are not recommended for use with CapSense.
Cypress Semiconductor Corporation
Document Number: 001-53304 Rev. *L
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised May 20, 2011
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
