CM6802A/B/AH/BH (Dynamic Soft PFC/Green PWM)
http://www.championmicro.com.tw
EPA/80++ ZVS-Like PFC/PWM COMBO CONTROLLER
Design for High Efficient Power Supply at both Full Load and Light Load
GENERAL DESCRIPTION
FEATURES
Switching to CM6802A/B/AH/BH from your existing
CM6800 family boards can gain the following advanced
performances:
Patents Pending
Pin to pin compatible with CM6800,CM6800A,
ML4800 and FAN4800.
1.) Around 2% efficiency gain when the output load is
below 40% of the full load.
23V Bi-CMOS process.
Designed for EPA/80++ efficiency.
2.) Hold Up time can be increased ~ 30% from the
existing 6800 power supply.
CM6802A/B : Selectable Boost output from 380V to
300V during light load.
3.) 420V bulk capacitor value may be reduced PFC
boost ripple current can be reduced; therefore, the
boost inductor core size maybe reduced.
CM6802AH/BH: Selectable Boost output from 380V to
342V during light load.
4.) No Load Consumption can be reduced 290mW at
270VAC.
All high voltage resistors can be greater than 4.7 Mega
ohm (4.7 Mega to 8 Mega ohm) to improve the no load
consumption.
5.) PWM transformer size can be smaller.
6.) To design 12V, 5V and 3.3V output filters can be
easy.
Rail to rail CMOS Drivers with on, 60 ohm and off, 30
ohm for both PFC and PWM with two 17V zeners.
7.) The stress over the entire external power device is
reduced and EMI noise maybe reduced.
Fast Start-UP Circuit without extra bleed resistor to aid
VCC reaches 13V sooner.
8.) Monotonic Output design is easy and more…Of
cause, the cost will be reduced.
Low start-up current (55uA typ.)
Low operating current (2.5mA typ.)
16.5V VCC shunt regulator
CM6802A/B/AH/BH is pin to pin compatible with CM6800
family.
Beside all the goodies in the CM6800, it is designed to meet
the EPA/80+ regulation. With the proper design, its
efficiency of power supply can easily approach 85%.
Leading Edge Blanking for both PFC and PWM.
fRTCT = 4*fpfc =4*fpwm for CM6802A//AH
fRTCT = 4*fpfc =2*fpwm for CM6802B/BH
To start evaluating CM6802A/B/AH/BH from the exiting
CM6800,CM6800A or ML4800 board, 6 things need to be
taken care before doing the fine tune:
Dynamic Soft PFC to ease the stress of the Power
Device and Ease the EMI filter design.
1.) Change RAC resistor (on pin 2, IAC) from the old
value to a higher resistor value between 4.7 Mega
ohms to 8 Mega ohms.
PFC Brown Out and PWM Brown Out
Internally synchronized leading edge PFC and trailing
edge PWM in one IC to Reduces ripple current in the
420V storage capacitor between the PFC and PWM
sections.
2.) Change RTCT pin (pin 7) from the existing value to
RT=7.75K ohm and CT=1000pF to have
fpfc=55Khz, fpwm=55Khz, frtct=220Khz.
Low total harmonic distortion, THD and Power Factor
approaches 1.0.
3.) Adjust all high voltage resistor around 5 mega ohm
or higher.
Average current, continuous or discontinuous boost
leading edge PFC.
4.) VRMS pin (pin 4) needs to be 1.125V at
VIN=85VAC for universal input application from line
input from 85VAC to 270VAC. Both poles for the
Vrms of the CM6802A/B/AH/BH needs to
substantially slow than CM6800 about 5 to 10 times.
PWM configurable for current mode or feed-forward
voltage mode operation.
Current fed Gain Modulator for improved noise immunity.
Gain Modulator is a constant maximum power limiter.
5.) At full load, the average Veao needs to around 4.5V
and the ripple on the Veao needs to be less than
250mV.
Brown-out control, over-voltage protection, UVLO, and
soft start, and Reference OK.
6.) Soft Start pin (pin 5), the soft start current has been
reduced
from
CM6800’s
20uA
to
PWM Short Circuit Protection
CM6802A/B/AH/BH’s 10uA.Soft Start capacitor can
be reduced to 1/2 from your original CM6800
capacitor.
Power Fold Back Protection
Green Mode PWM for less no load consumption.
2009/11/02 Rev. 1.4
Champion Microelectronic Corporation
1
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
