Document 511-1
SMT Data Line EMI Filters
–
CCDLF
• Available in 10 and 8-line versions
• See our PDLF series for 4, 3 and 2-line EMI filters
• Exceptional common mode noise attenuation from 15 MHz to
300 MHz;passes signal line data below 300 MHz with minimal
attenuation
• DC current capacity of 500 or 100 mA.
• Excellent electrical isolation (300 Vrms)
Designer’s Kit D303 contains four each of all values plus DLF and
PDLF filters
Core material Ferrite
Terminations RoHS compliant tin-silver-copper over silver-platinum.
Other terminations available at additional cost.
Weight CCDLF 8000: 540 mg; CCDLF 8500: 559 mg;
CCDLF 10000: 670 mg
Ambient temperature –40°C to +85°C
Storage temperature Component: –40°C to +85°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Current
L min
DCR max
(mOhms)
Mean Time Between Failures (MTBF) 26,315,789 hours
Part number1
Lines max (mA)2 (µH)3
Packaging 1000/13″ reel Plastic tape: 16 mm wide
CCDLF8x00: 10.46 mm thick, 12 mm pocket spacing,
4.5 mm pocket depth
CCDLF10000: 10.28 mm thick, 12 mm pocket spacing,
5.0 mm pocket depth
CCDLF 10000L_
CCDLF 8000L_
CCDLF 8500L_
10
8
8
100
100
500
5
5
5
250
250
200
PCB washing Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf
1. When ordering, please specify termination and packaging codes:
CCDLF 8500LD
Termination L = RoHS compliant tin-silver-copper over silver-platinum
Special order: S = non-RoHS tin-lead (63/37).
Packaging D = 13″ machine ready reel. EIA-481 embossed plastic
*
Typical Response
tape (1000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
-10
Differential Mode
2. Current rating is for each line.
0
3. Inductance is per winding, tested at 1 MHz.
4. Operating temperature range -40°C to +85°C.
5. Electrical specifications at 25°C.
10
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
20
Common Mode
30
0.1
1
10
100
1000
Frequency (MHz)
*Measured on HP 8753D network analyzer. Ref: 50 Ohms.
Document 511-1 Revised 11/19/10
US +1-847-639-6400 sales@coilcraft.com
UK +44-1236-730595 sales@coilcraft-europe.com
Taiwan +886-2-2264 3646 sales@coilcraft.com.tw
China +86-21-6218 8074 sales@coilcraft.com.cn
Singapore + 65-6484 8412 sales@coilcraft.com.sg
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.