Document 439
For Texas Instruments TPS23750
Flyback Transformers PoE Powered Device Controller
• Isolated synchronous flyback transformers developed for
Texas Instruments PMP929 reference design.
• Operates up to 500 kHz with 18 – 72 V input
• 1500 Vrms isolation primary and bias to secondary windings
Core material Ferrite
Terminations RoHS tin-silver over tin over nickel over phos
bronze. Other terminations available at additional cost.
Weight 5.0 – 5.3 g
Ambient temperature –40°C to +125°C
Storage temperature Component: –40°C to +125°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 200 per 13″ reel Plastic tape: 44 mm wide,
0.35 mm thick, 28 mm pocket spacing, 9.6 mm pocket depth
PCB washing Only pure water or alcohol recommended
LeakageL5
L at 0 A2 L at Ipk3
DCR max (Ohms)
max(µH)
Turns ratio
Part
±10%
min
Ipk3
Drive
output
number1 (µH)
(µH)
pri
sec4 drive bias pri drive pri:sec6 pri:drive pri:bias (A)
Output7
C1173-AL_ 166.5
C1174-AL_ 150.0
150.0 0.770 0.020 0.523 1.12 2.50 0.400 6.5:1
135.0 0.515 0.023 0.570 0.88 2.00 0.400 5.0:1
3.7:1
3.2:1
2.0:1
1.2 3.3 V, 3A 5.6 V, 10 mA
2.25:1 1.2 5.0 V, 2A 7.5 V, 10 mA
1. When ordering, please specify packaging code:
C1174-ALD
4. DCR for secondary is with windings connected in parallel.
5. Leakage inductance for the primary is with the secondary and drive
windings shorted; leakage inductance for the drive winding is with the
secondary windings shorted.
Packaging: D = 13″ machine ready reel. EIA-481 embossed plastic
tape (200 per full reel).
6. Turns ratio is with both secondary windings connected in parallel.
B = Less than full reel. In tape, but not machine ready. To
have a leader and trailer added ($25 charge), use
code letter D instead.
7. Output of the secondary is with the windings connected in parallel. Bias
winding output is 10 V, 20 mA.
8. Electrical specifications at 25°C.
2. Inductance is for the primary, measured at 100 kHz, 0.1 Vrms.
3. Peak primary current drawn at minimum input voltage.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Dot indicates pin 1
0.07
1,79
12
11
0.135
3,43
0.028
0,72
0.665
16,88
3
1
12
1
6
12
7
Primary
Secondary
0.677
17,20
max
YYXXXX-AL
9
10
5
8
Drive
7
2
0.098
2,5
0.098
2,5
Recommended
Land Pattern
0.865
max
Bias
21,97
1
0.335
8,51
The secondary windings are to be
connected in parallel on the PC board.
max
0.004/0,10
0.590
14,98
0.079
2,01
0.693
17,60
inches
mm
Dimensions are in
Specifications subject to change without notice.
Please check our website for latest information.
Document439 Revised10/28/08
© Coilcraft, Inc. 2009