BL9110
1A Low Dropout, Low Quiescent Current
High PSRR CMOS Linear Regulator
Electrical Characteristics (Note 5)
BL9110-1.2V Electrical Characteristics
(VDD=2.5V, VOUT=1.2V, CE=VDD, CIN=2.2F, COUT=2.2F, TA=25°C , unless otherwise noted.)
Parameter
Input Voltage
Output Voltage Accuracy (Note 6)
Symbol
VDD
Conditions
MIN
2.5
-1
-2
1.0
TYP MAX
unit
V
6
+1
IOUT=1mA
%
VOUT
+2
1.3
Current Limit
Short Circuit Current
Quiescent Current
Standby Current
ILIM
ISCC
IQ
A
VOUT=0
IOUT=0mA
VCE=GND, Shutdown
250
70
0.01
mA
uA
uA
120
1
ISTBY
IOUT=300mA
420
715
Dropout Voltage (note 7)
VDROP
mV
IOUT=1A
870 1310
Line Regulation (Note 8)
Load Regulation (Note 9)
ΔVLINE
ΔVLOAD
2.5V≤VDD≤ 6V, IOUT=100mA
1mA≤IOUT≤1A
0.05
20
0.5
%/V
mV
Output Voltage (Note 10)
Temperature Coefficient
IOUT=100mA
-40°C ≤T≤85°C
Shutdown
TCVOUT
±100
ppm/°C
Logic Low
Logic High
VIL
VIH
0.4
V
V
CE
Input Threshold
Start up
1.0
CE Pull-down Resistance
Output Noise Voltage
f=1kHz
RCE
eNO
5
45
MΩ
uVRMS
10Hz to100KHz, IOUT=1mA
70
60
(VOUT≤3.3V)
Power Supply
Rejection Ratio
0.2VP-P Ripple
IOUT=100mA
PSRR
dB
f=1kHz
(VOUT>3.3V)
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
Output Discharge Resistance
TSD
TSDHY
RDSC
Shutdown, Temp increasing
165
30
50
°C
°C
Ω
Note 5: 100% production test at +25°C. Specifications over the temperature range are guaranteed by design and
characterization.
Note 6: This IC includes two kinds of output voltage accuracy versions. A: ±1%, B: ±2%.
Note 7: The required minimum input operating voltage is equal to VOUT+VDROP, and if VOUT+VDROP <2.5V, the required
minimum input operating voltage must be set to 2.5V. VOUT is the normal output voltage, e.g. VOUT=2.8V for 2.8V fixed
output version.
VOUT1 VOUT 2
VDD VOUT
Note 8: Line regulation is calculated by
VLINE
100
Where VOUT1 is the output voltage when VDD1=6.0V, VOUT2 is the output voltage when VDD2= max (VOUT+0.5V, 2.5V).
△VDD=VDD1-VDD2
.
Note 9: Load regulation is calculated by
VLOAD VOUT1 VOUT 2
Where VOUT1 is the output voltage when IOUT1=1mA, and VOUT2 is the output voltage when IOUT2=1A.
VOUT
T VOUT
Note 10: The temperature coefficient is calculated by
TCV
OUT
PPMIC BU
BL9110 Rev 2.0
04/2016
www.belling.com.cn
6
Belling Proprietary Information. Unauthorized Photocopy and Duplication Prohibited
© 2011 Belling All Rights Reserved