BD Series
Standard Profile DIP Switches
Vertical Full Profile DIP
QUANTITY
PART NUMBER
NO.POS.
DIM.
‘
A’
DIM.
‘B’
PER TUBE
Ø.038 TYP.
(0,97)
.062
BD01
BD02
BD03
BD04
BD05
BD06
BD07
BD08
BD09
BD10
BD12
1
2
.180 (4,57)
.280 (7,11)
NA
115
74
54
43
35
30
26
23
21
19
16
(1,58) MAX
ACTUATOR
TRAVEL
H
.100 (2,54)
.200 (5,08)
.100 TYP.
(2,54)
DIM 'A'
3
.380 (9,65)
ON
4
.480 (12,19)
.580 (14,73)
.680 (17,27)
.780 (19,81)
.880 (22,35)
.980 (24,89)
1.080 (27,43)
1.280 (32,51)
.300 (7,62)
.380
(9,65)
.297
(7,55)
5
.400 (10,16)
.500 (12,75)
.600 (15,24)
.700 (17,78)
.800 (20,32)
.900 (22,.86)
1.100 (27,94)
6
BD08
2
3
4
5
6
7
8
1
7
.160 TYP.
(4,06)
DIM 'B'
8
.059 TYP.
(1,5)
9
.080 TYP.
(2,03)
10
12
.265
(6,73)
.032
(0,82)
TYP.
.030
(0,77)
Schematic
.006
(0,16)
.089
(2,26)
SPST
.020 TYP.
(0,51)
.100 TYP.
(2,54)
.297
(7,55)
.141 TYP.
(3,58)
Open Base and AV Right Angle Terminal Style
0.050
(1,27)
.089
(2,26)
QUANTITY
PER TUBE
0.030
(0,77)
PART NUMBER
NO.POS.
DIM. ‘A’
0.297
(7,55)
BD02AV
BD03AV
BD04AV
BD05AV
BD06AV
BD07AV
BD08AV
BD09AV
BD10AV
BD12AV
2
3
.280 (7,11)
.380 (9,65)
72
52
42
35
29
26
23
20
18
15
BD08AV
4
.480 (12,19)
.580 (14,73)
.680 (17,27)
.780 (19,81)
.880 (22,35)
.980 (24,89)
1.080 (27,43)
1.280 (32,51)
0.061 TYP.
(1,55)
.032
(0,82)
TYP.
5
DIM.A
6
7
ON
1
.080
(2,03)
8
.380
(9,65)
9
.125
(3,18)
2
3
4
5
6
7
8
10
12
.020 TYP.
(0,51)
.010
(0,25)
Schematic
.100 TYP.
(2,54)
.006
(0,16)
.100
(2,54)
.320
(8,12)
.100
(2,54)
SPST
.100 TYP.
(2,54)
.046 DIA TYP.
(1,17ø)
Installation, Soldering and Cleaning
All BD Series Standard Profile DIP Switches can be hand soldered or machine soldered without the use of boot, caps,
tapes or special attention. Open base washable models have unique design, allowing solvent cleaners and water/detergent
solutions to flush and clean the electrical contacts of the contaminants and fluxes. For best results, follow these directions:
1) Wave soldering recommended at 500° F (260ºC) solder temperature.
2) Hand solder using 30 watt small tip iron controlled at 500° F (260ºC), 10 seconds max./terminal.
3) Open base washable models: Clean flux using forced rinse, high agitation or triple bath cleaning method.
DO NOT mask or cover switch in any way during cleaning. Switch is designed for easy solvent flush out.
4) All switch actuators must be in ‘OFF’ position during soldering and cleaning processes.
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
15 Mar 22
www.ckswitches.com
H–19