BD Series
Standard Profile DIP Switches
Features/Benefits
Typical Applications
•
•
•
Traditional full profile DIP switch
Extended actuator for easy actuation
Open bottom construction allows for
solder washing without the need
for tape seal
•
•
•
Address switch for industrial controls
Logic switching for computers and peripherals
Function controlling for
numerous applications
H
•
RoHS compliant
VIBRATION: No contact opening greater than 10 microseconds and no
contact closure when exposed to vibration .06 in DA or 5g,
whichever is less, from 10 to 55 Hz, and 10g from 55 to 500 Hz.
Specifications
SWITCH FUNCTION: SPST - 1 thru 12 position available
(except 11 position).
SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E
method 9 (1 hour steam aging).
CONTACT RATING:
PACKAGING: Switches supplied in rigid dispensing tubes in full-tube
quantities only: this may effect order quantity. Number of switches
per tube varies with model. Switch position 1 denotes pin number
1. All switch actuators in ‘OFF’ position, standard.
Carry: 100 mA max. @ 50 V DC.
Switch: 100 mA max. @ 5 V DC or 25 mA max. @ 25 V DC.
MECHANICAL AND ELECTRICAL LIFE: 10,000 make-and-break
cycles at full load, each circuit.
Materials
CASE & COVER: Glass filled polyester (PBT),
CONTACT RESISTANCE: Below 50 milliohms typ. initial
@ 2-4 V DC 100mA.
INSULATION RESISTANCE: 109 ohms min.
flame retardant (UL 94V-0).
DIELECTRIC STRENGTH: 500 V RMS min. @ sea level between
adjacent terminals.
ACTUATOR: Glass filled nylon 6/6, flame retardant,
heat stabilized (UL 94V-0)
CAPACITANCE: 5pF max. between adjacent terminals.
STORAGE & OPERATING TEMPERATURE: -40°C to 85°C.
CONTACTS: Gold over nickel over phosphor bronze.
TERMINALS: Matte-tin over nickel over phosphor bronze.
SHOCK: Withstands 20g 11 ms sawtooth waveform with no con-
tact opening greater than 10 microseconds.
Note: Specifications and materials listed above are for switches with standard options.
For information on specific and custom switches, consult Customer Service Center.
Vertical Full Profile DIP
QUANTITY
PART NUMBER
NO.POS.
DIM.
‘A’
DIM.
‘B’
PER TUBE
Ø.038 TYP.
(0,97)
.062
BD01
BD02
BD03
BD04
BD05
BD06
BD07
BD08
BD09
BD10
BD12
1
2
.180 (4,57)
.280 (7,11)
NA
115
74
54
43
35
30
26
23
21
19
16
(1,58) MAX
ACTUATOR
TRAVEL
.100 (2,54)
.200 (5,08)
.100 TYP.
(2,54)
DIM 'A'
3
.380 (9,65)
4
.480 (12,19)
.580 (14,73)
.680 (17,27)
.780 (19,81)
.880 (22,35)
.980 (24,89)
1.080 (27,43)
1.280 (32,51)
.300 (7,62)
ON
5
.400 (10,16)
.500 (12,75)
.600 (15,24)
.700 (17,78)
.800 (20,32)
.900 (22,.86)
1.100 (27,94)
.380
.297
(7,55)
(9,65)
6
BD08
2
3
4
5
6
7
8
1
7
8
.160 TYP.
(4,06)
DIM 'B'
9
.059 TYP.
(1,5)
.080 TYP.
(2,03)
10
12
.265
(6,73)
.032
(0,82)
TYP.
Schematic
.030
(0,77)
SPST
.006
(0,16)
.089
(2,26)
.020 TYP.
(0,51)
.100 TYP.
(2,54)
.297
(7,55)
.141 TYP.
(3,58)
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
www.ck-components.com
H–16