Datasheet > AQ533

AQ533

更新时间： 2022-04-23 23:00:11

品牌	Logo	应用领域
ACUTECH		稳压器
页数	文件大小	规格书
10页	634K
描述
Ultra-Low Dropout 500mA Voltage Regulator

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

AQ533 数据手册

Acutechnology Semiconductor Inc.

AQ533

The AQ533 provides Reverse Current Protection. When the AQ533 is turned off, no

current will flow from the output to input. A small current will flow from output to ground

through the Vout set resistors R1 and R2. The need for protection diodes is eliminated.

6. Thermal Considerations

When an integrated circuit operates with an appreciable current, its junction temperature is

elevated. It is important to quantify its thermal limits in order to achieve acceptable

performance and reliability. This limit is determined by summing the individual parts

consisting of a series of temperature rises from the semiconductor junction to the operating

environment. The heat generated at the device junction flows through the die to the die

attach pad, through the lead frame to the surrounding case material, to the printed circuit

board, and eventually to the ambient environment.

The AQ533 regulators have internal thermal shutdown to protect the device from over-

heating. Under all possible operating conditions, the junction temperature of the AQ533

must be lower than 125°C. A heatsink may be required depending on the maximum power

dissipation and maximum ambient temperature of the application.

To determine if a heatsink is needed, the power dissipated by the regulator, P_D, must be

calculated:

P_D= (V_IN-V_OUT) I_L

where the I_Lis the load current.

The next parameter, which must be calculated, is the max. allowable temperature rise, T(max):

T(max)=T_J(max)-T_A(max)

where T_J(max) is the maximum allowable junction temperature (125°C), and T_A(max) is the

maximum ambient temperature, which will be encountered in the application.

Using the calculated values for T(max) and P_D, the maximum allowable value for the

junction to ambient thermal resistance (θ_JA) can be calculated:

θ_JA=T(max)/ P_D

If the maximum allowable value for θ_JAis found to be greater than the junction to ambient

thermal resistance for the package used, no heatsink is needed since the package alone will

dissipate enough heat to satisfy these requirements.

7. Ultra low Dropout Operation

The AQ533 allows for ultra low dropout operation by connecting the pin ENABLE to >0.95V + Vout.

This results in a dropout of 350 mV at 500 mA of load current, between Vin and VOUT.

This feature is important when the supply voltage is dropping near the output regulated voltage.

Furthermore if the voltage dropout is low, the internal power dissipation is also reduced and the

thermal requirements of the device are less stringent.

www.acutechnology.com

Rev. 1.7 September 13, 2006

1...5 6 789 10

下载PDF

与AQ533相关器件

型号	品牌	描述	获取价格	数据表
AQ533CY-M5-18-TR	ACUTECH	Ultra-Low Dropout 500mA Voltage Regulator	获取价格
AQ533CY-M5-18-TRL	ACUTECH	Ultra-Low Dropout 500mA Voltage Regulator	获取价格
AQ533CY-M5-25-TR	ACUTECH	Ultra-Low Dropout 500mA Voltage Regulator	获取价格
AQ533CY-M5-25-TRL	ACUTECH	Ultra-Low Dropout 500mA Voltage Regulator	获取价格
AQ533CY-M5-33-TR	ACUTECH	Ultra-Low Dropout 500mA Voltage Regulator	获取价格
AQ533CY-M5-33-TRL	ACUTECH	Ultra-Low Dropout 500mA Voltage Regulator	获取价格