CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
New!
@Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte.
PXK
@Rated voltage range : 2.5 to 16Vdc, Capacitance range : 100 to 560MF
@Suitable for DC-DC converters, voltage regulators and decoupling applications used to
computer motherboards etc.
Downsized
PXE
@RoHS Compliant
SPECIFICATIONS
?
Items
Characteristics
Category
Temperature Range
-55 to +105C
Rated Voltage Range 2.5 to 16Vdc
Capacitance Tolerance P20% (M)
(at 20C, 120Hz)
(at 105C)
Surge Voltage
Rated voltageB1.15V
Leakage Current
Shall not exceed values shown in STANDARD RATINGS.
(at 20C after 2 minutes)
Dissipation Factor
(tane)
0.12 max.
(at 20C, 120Hz)
Low Temperature
Characteristics
Z(
-
25C)/Z(+20C)[1.15
(Max. Impedance Ratio) Z(
-55C)/Z(+20C)[1.25
(at 100kHz)
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2,000 hours
(F46 : 1,000 hours) at 105C.
Appearance
Capacitance change
DF (tanE)
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
ESR
Leakage current
Bias Humidity
Surge Voltage
Failure Rate
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at
60C, 90 to 95% RH for 1,000 hours (F46 : 500hours).
Appearance
Capacitance change
DF (tanE)
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
ESR
Leakage current
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
Capacitance change
DF (tanE)
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
ESR
Leakage current
0.5% per 1,000 hours maximum (Confidence level 60% at 105C)
*Note : If any doubt arises, measure the leakage current after following voltage treatment.
Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105C.
DIMENSIONS [mm]
MARKING
?
?
@Terminal Code : A
EX) 2.5V330MF
W
K89A
330
2.5V
Size Code fD
L
A
B
C
W
P
E61
F46
F61
5
5.8 5.3 5.3 5.9 0.5 to 0.8 1.4
6.3 4.5 6.6 6.6 7.2 0.5 to 0.8 1.9
6.3 5.8 6.6 6.6 7.2 0.5 to 0.8 1.9
0.3max.
AP0.2
LP0.3 (Note)
Note : L+0.1/-0.2 for F46
PART NUMBERING SYSTEM
?
1
2
3
4
5
6
7
8
9
10
11 12 13
14
15 16 17
18
A P X K A A A A R A A A A M A A A G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 330MF:331, 560MF:561)
Taping code
Terminal code
Voltage code (ex. 2.5V:2R5, 6.3V:6R3)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
(1/2)
CAT. No. E1001K