5秒后页面跳转
AN731 PDF预览

AN731

更新时间: 2024-11-28 22:29:19
品牌 Logo 应用领域
威世 - VISHAY 转换器
页数 文件大小 规格书
7页 76K
描述
Simple Solution for Dynamically Programming the Output Voltage of DC-DC Converters

AN731 数据手册

 浏览型号AN731的Datasheet PDF文件第2页浏览型号AN731的Datasheet PDF文件第3页浏览型号AN731的Datasheet PDF文件第4页浏览型号AN731的Datasheet PDF文件第5页浏览型号AN731的Datasheet PDF文件第6页浏览型号AN731的Datasheet PDF文件第7页 
AN731  
Vishay Siliconix  
Simple Solution for Dynamically Programming the  
Output Voltage of DC-DC Converters  
INTRODUCTION  
Figure1showsatypicaldc-to-dcconverterconfiguration. Asin  
many PWM controllers, the non-inverting input of the voltage  
feedback error amplifier is internally connected to the  
reference voltage, Vr. The output voltage of the converter is set  
by a resistor divider network R1 and R2. This configuration  
enables a fixed output voltage that is equal to or greater than  
the reference voltage. But in many power conversion designs,  
it is useful to vary the output to a value lower than the reference  
voltage and to dynamically adjust the output voltage. The  
op-amp circuit shown in Figure 3 gives designers a simple way  
to do this. Scaling the output voltage with respect to a control  
voltage VC is totally flexible. This application note describes  
how to use this simple solution and provides a step-by-step  
designproceduretoassistdesignersincalculatingthespecific  
parameters required by their circuits.  
DESIGN REQUIREMENT  
Reference voltage, Vr  
Control voltage: VC = VC1 to VC2  
Output voltage: VO = VO1 at VC = VC1, VO = VO2 at VC = VC2  
and VO is linear for any value of VC in its range.  
,
These design requirements are shown in Figure 2. The output  
voltage is a linear function with respect to the control voltage.  
The function crosses two end points A = (VC1, VO1) and B =  
(VC2, VO2).  
V
O
(V)  
Power Stage  
PWM  
V
IN  
V
OUT  
B (V , V  
)
C2  
O2  
R1  
R2  
FB  
+
V
r
EA  
A (V , V  
)
C1  
O1  
PWM Controller  
V
C
(V)  
FIGURE 1. Typical DC/DC Converter Configuration  
FIGURE 2. Output Voltage vs Control Voltage Requirement  
Power Stage  
PWM  
V
IN  
V
OUT  
R1  
FB  
A
R3  
+
V
r
EA  
R2  
R4  
B
PWM Controller  
V
C
+
V
r2  
V
X
LM358  
Op-Amp Circuit  
FIGURE 3. Op-Amp Circuit Offers Programmable Output Function  
Document Number: 71128  
28-Jan-00  
www.vishay.com S FaxBack 408-970-5600  
1

与AN731相关器件

型号 品牌 获取价格 描述 数据表
AN7310 ETC

获取价格

SEMICONDUCTORS
AN7310N PANASONIC

获取价格

Dual Pre-Amplifier for Car Radio
AN7311 PANASONIC

获取价格

Dual Pre-Amplifier for Car Stereo
AN73116 PANASONIC

获取价格

Audio Preamplifier, 1 Channel(s), 1 Func, Bipolar, PDIP16
AN73117 PANASONIC

获取价格

Audio Preamplifier, 1 Channel(s), 1 Func, Bipolar, PDIP16
AN73118 PANASONIC

获取价格

Audio Preamplifier, 1 Channel(s), 1 Func, Bipolar, PDSO16
AN7312 PANASONIC

获取价格

DUAL RECORDING /PLAYBACK PRE AMPLIFIER CIRCUIT WITH ALC
AN7315 PANASONIC

获取价格

Low Voltage Dual Pre-Amplifier Circuits
AN7315S PANASONIC

获取价格

Low Voltage Dual Pre-Amplifier Circuits
AN7316 PANASONIC

获取价格

DUAL RECORDING AND PLAYBACK PRE-AMPLIFIER IC FOR SINGLE/DOUBLE CASSETTE