AH3382
Absolute Maximum Ratings (Notes 5 & 6) (@TA = +25°C, unless otherwise specified.)
Symbol
VDD
Characteristic
Value
32
Unit
V
Supply Voltage (Note 6)
Reverse Supply Voltage (Note 6)
Output Off Voltage (Note 6)
Continuous Output Current
-32
32
V
VDDR
V
VOUT_MAX
IOUT
IOUT_R
B
60
mA
Reverse Output Current
Magnetic Flux Density
-50
mA
Unlimited
SIP-3 (Ammo Pack),
SIP-3 (Bulk Pack)
550
Package Power Dissipation
mW
PD
SC59 and SOT23
230
-65 to +165
+150
Ts
TJ
Storage Temperature Range
C
C
kV
Maximum Junction Temperature
ESD HBM
Electros Static Discharge Withstand - Human Body Model (HBM)
6
Notes:
5. Stresses greater than the 'Absolute Maximum Ratings' specified above may cause permanent damage to the device. These are stress ratings only;
functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device reliability may be
affected by exposure to absolute maximum rating conditions for extended periods of time.
6. The absolute maximum VDD of 32V is a transient stress rating and is not meant as a functional operating condition. It is not recommended to
operate the device at the absolute maximum rated conditions for any period of time.
Recommended Operating Conditions (@TA = -40°C to +125°C , unless otherwise specified.)
Symbol
VDD
Parameter
Supply Voltage
Operating Temperature Range
Condition
Rating
3.0 to 28
Unit
V
Operating
Operating
-40 to +125
TA
C
Electrical Characteristics (Note 7 & 8) (@TA = -40°C to +125°C , VDD = 3V to 28V, unless otherwise specified.)
Symbol
Parameter
Output ON Voltage
Condition
IOUT = 20mA, B > BOP
Min
Typ
Max
Unit
VOUT_ON
-
0.2
0.4
V
Output Leakage Current
(When output is off)
ILKG
-
<0.1
10
µA
VOUT = 28V, B < BRP, Output off
-
-
3
-
3.5
4
mA
mA
k
Output open, TA = +25C
Output open, TA = -40C to +125C
TA = -40°C to 125°C,
VDD >= 3V, B > BOP (Note 7)
-
Supply Current
IDD
Internal Pull-Up Resistance
Device Start-Up Time
Chopping Frequency
10
-
14
10
800
18
-
RPU
tST
fC
µs
-
-
kHz
Response Time Delay
(Time from magnetic threshold
reached to the start of the output rise
or fall)
(Note 9)
-
3.75
-
µs
tD
Output Rising Time
(External pull-up resistor RL and load
capacitance dependent)
Output Falling Time
(Internal switch resistance and load
capacitance dependent)
-
-
0.2
0.1
1
1
µs
µs
tR
RL = 1kΩ, CL = 20pF
RL = 1kΩ, CL = 20pF
tF
Output Current Limit
Zener Clamp Voltage
30
28
-
-
55
-
mA
V
IOCL
VZ
B > BOP, (Note 10 )
IDD = 5mA
Notes:
7. When power is initially turned on, VDD must be within its correct operating range (3.0V to 28V) to guarantee the output sampling. The output state is valid
after the start-up time of 10s typical from the operating voltage reaching 3V.
8. Typical values are defined at TA = +25C, VDD = 12V. Maximum and minimum values over the operating temperature range is not tested in production but
guaranteed by design, process control and characterization.
9. Guaranteed by design, process control and characterization, Not tested in production.
10. The device will limit the output current IOUT to current limit of IOCL.
3 of 14
www.diodes.com
May 2018
© Diodes Incorporated
AH3382
Document number: DS38921 Rev. 2 - 2