AFBR-5715PZ

更新时间： 2024-01-07 12:17:35

品牌	Logo	应用领域
安华高科 - AVAGO		光纤放大器通信
页数	文件大小	规格书
20页	508K
描述
Families of Multi-Mode Small Form Factor Pluggable (SFP) Optical Transceivers

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

AFBR-5715PZ 技术参数

是否Rohs认证：	符合	生命周期：	Transferred
Reach Compliance Code：	compliant	ECCN代码：	EAR99
HTS代码：	8517.62.00.50	风险等级：	5.71
Is Samacsys：	N	主体宽度：	16.25 mm
主体高度：	12.1 mm	主体长度或直径：	42.3 mm
内置特性：	AMPLIFIER	通信标准：	GR-468
连接类型：	LC CONNECTOR	数据速率（发送）：	1250 Mbps
发射极/检测器类型：	LASER DIODE	光纤设备类型：	TRANSCEIVER
光纤类型：	50/125, MMF	JESD-609代码：	e4
安装特点：	PANEL MOUNT	最高工作温度：	85 °C
最低工作温度：	-10 °C	最大工作波长：	860 nm
最小工作波长：	830 nm	标称工作波长：	850 nm
标称光功率输出：	0.223 mW	灵敏度：	-21 dBm
子类别：	Fiber Optic Transceivers	最大供电电压：	3.465 V
最小供电电压：	3.135 V	标称供电电压：	3.3 V
表面贴装：	NO	端子面层：	Gold (Au)
Base Number Matches：	1

AFBR-5715PZ 数据手册

Table 2. Pin Description

Engagement

Order(insertion)

Name

Function/Description

Notes

VeeT

Transmitter Ground

TX Fault

TX Disable

MOD-DEF2

MOD-DEF1

MOD-DEF0

Rate Selection

LOS

Transmitter Fault Indication

Transmitter Disable - Module disables on high or open

Module Deﬁnition 2 - Two wire serial ID interface

Module Deﬁnition 1 - Two wire serial ID interface

Module Deﬁnition 0 - Grounded in module

Not Connected

Loss of Signal

VeeR

Receiver Ground

VeeR

Receiver Ground

VeeR

Receiver Ground

RD-

Inverse Received Data Out

Received Data Out

RD+

VeeR

Reciver Ground

VccR

Receiver Power -3.3 V 5ꢀ

Transmitter Power -3.3 V 5ꢀ

Transmitter Ground

VccT

VeeT

TD+

Transmitter Data In

TD-

Inverse Transmitter Data In

Transmitter Ground

VeeT

Notes:

1. TX Fault is an open collector/drain output which should be pulled up externally with a 4.7KΩ – 10 KΩ resistor on the host board to a supply

<VccT+0.3 V or VccR+0.3 V. When high, this output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the

output will be pulled to < 0.8 V.

2. TX disable input is used to shut down the laser output per the state table below. It is pulled up within the module with a 4.7-10 KΩ resistor.

Low (0 – 0.8 V):

Transmitter on

Between (0.8 V and 2.0 V):

High (2.0 – 3.465 V):

Open:

Undeﬁned

Transmitter Disabled

3. Mod-Def 0,1,2. These are the module deﬁnition pins. They should be pulled up with a 4.7-10 KΩ resistor on the host board to a supply less

than VccT +0.3 V or VccR+0.3 V.

Mod-Def 0 is grounded by the module to indicate that the module is present

Mod-Def 1 is clock line of two wire serial interface for optional serial ID

Mod-Def 2 is data line of two wire serial interface for optional serial ID

4. LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7 K – 10 KΩ resistor on the host board to a

supply < VccT,R+0.3 V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as deﬁned by

the standard in use). Low indicates normal operatio0n. In the low state, the output will be pulled to < 0.8 V.

5. RD-/+: These are the diﬀerential receiver outputs. They are AC coupled 100 Ω diﬀerential lines which should be terminated with 100 Ω diﬀerential

at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines

must be between 370 and 2000 mV diﬀerential (185 – 1000 mV single ended) according to the MSA. Typically it will be 1500mv diﬀerential.

6. VccR and VccT are the receiver and transmitter power supplies. They are deﬁned as 3.135 – 3.465 V at the SFP connector pin. The in-rush current

will typically be no more than 30 mA above steady state supply current after 500 nanoseconds.

7. TD-/+: These are the diﬀerential transmitter inputs. They are AC coupled diﬀerential lines with 100 Ω diﬀerential termination inside the module.

The AC coupling is done inside the module and is thus not required on the host board. The inputs will accept diﬀerential swings of 500 – 2400

mV (250 – 1200 mV single ended). However, the applicable recommended diﬀerential voltage swing is found in Table 5.

1...5 6 789 10 11...20

下载PDF

与AFBR-5715PZ相关器件

型号	品牌	描述	获取价格	数据表
AFBR-5715PZ-JU1	AVAGO	Families of Multi-Mode Small Form Factor Pluggable (SFP) Optical Transceivers with Optiona	获取价格
AFBR-5725PZ	AVAGO	FIBER OPTIC TRANSCEIVER	获取价格
AFBR-57D7APZ	AVAGO	16GFC SFP Digital Diagnostic SFP, 850 nm, 16G/8G/4G Low Voltage (3.3 V) Fibre Channel Opti	获取价格
AFBR-57F5MZ	AVAGO	16GFC SFP Digital Diagnostic SFP, 850 nm, 16G/8G/4G Low Voltage (3.3 V) Fibre Channel Opti	获取价格
AFBR-57F5PZ	AVAGO	Low Voltage (3.3V) Fibre Channel Optical Transceiver	获取价格
AFBR-57J5APZ	AVAGO	Digital Diagnostic SFP, 850nm 3.072/2.4576 Gb/s, RoHS OBSAI/CPRI Compatible Optical Transc	获取价格

与AFBR-5715PZ相关文章

STM32H743技术深度剖析与应用案例探索
2024-05-30

15
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
2024-05-30

15
74HC14芯片资料介绍：性能特性分析、引脚介绍
2024-05-30

13
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
2024-05-30

10

产品中心

服务支持

精选活动

关于我们

帮助中心

AFBR-5715PZ

AFBR-5715PZ 技术参数

AFBR-5715PZ 数据手册

与AFBR-5715PZ相关器件

与AFBR-5715PZ相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

AFBR-5715PZ

AFBR-5715PZ 技术参数

AFBR-5715PZ 数据手册

与AFBR-5715PZ相关器件

与AFBR-5715PZ相关文章

您还可以找

您在本页遇到什么问题？