Dual-Channel Isolators with
Integrated DC-to-DC Converters
ADuM6210/ADuM6211/ADuM6212
FUNCTIONAL BLOCK DIAGRAM
Data Sheet
FEATURES
isoPower integrated, isolated dc-to-dc converter
Regulated 3.15 V to 5.25 V output
Up to 150 mW output power
Dual dc-to-100 Mbps (NRZ) signal isolation channels
Soft start power supply
20-lead SSOP package with 5.3 mm creepage
Supports SPI up to 15 MHz
High temperature operation: 105°C
High common-mode transient immunity: >25 kV/µs
Safety and regulatory approvals
1
20
V
V
DD1
DD2
2
19 GND
ISO
GND
/V
P
2-CHANNEL iCoupler CORE
3
18
V
V
/V
V
V
OA IA
IA OA
ADuM6210/ADuM6211/
ADuM6212
4
17
/V
/V
IB OB
OB IB
GND
P
5
16
GND
GND
NC
ISO
ISO
GND
P
6
15
14
NC
7
8
PCS
OSC
13
PDIS
V
V
SEL
ISO
V
1.25V 12
9
DDP
UL recognition (pending)
GND
P
10
11
GND
RECT REG
ISO
3750 V rms for 1 minute per UL 1577
CSA Component Acceptance Notice #5A (pending)
VDE certificate of conformity (pending)
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
Figure 1. ADuM6210/ADuM6211/ADuM6212
V
IORM = 849 V peak
APPLICATIONS
RS-232 transceivers
Power supply start-up bias and gate drives
Isolated sensor interfaces
Industrial PLCs
GENERAL DESCRIPTION
The ADuM6210/ADuM6211/ADuM62121 are dual-channel
digital isolators with isoPower®, an integrated, isolated dc-to-
dc converter. Based on the Analog Devices, Inc., iCoupler®
technology, the dc-to-dc converter provides regulated, isolated
power that is adjustable between 3.15 V and 5.25 V. Input supply
voltages can range from slightly below the required output to
significantly higher. Popular voltage combinations and their
associated power levels are shown in Table 1.
Table 1. Power Levels
Input Voltage (V)
Output Voltage (V) Output Power (mW)
5
5
150
100
66
5
3.3
3.3
3.3
The ADuM6210/ADuM6211/ADuM6212 eliminate the need
for a separate, isolated dc-to-dc converter in low power, isolated
designs. The iCoupler chip-scale transformer technology is used for
isolated logic signals and for the magnetic components of the dc-
to-dc converter. The result is a small form factor, total isolation
solution.
isoPower uses high frequency switching elements to transfer
power through its transformer. Take special care during printed
circuit board (PCB) layout to meet emissions standards. See the
AN-0971 Application Note for board layout recommendations.
1
Protected by U.S. Patents 5,952,849; 6,873,065; 6,903,578; and 7,075,329. Other patents are pending.
Rev. 0
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rightsof third parties that may result fromits use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks andregisteredtrademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Technical Support
©2013 Analog Devices, Inc. All rights reserved.
www.analog.com