16-/32-Channel, Serially Controlled 4 ꢀ
1.8 V to 5.5 V, ꢁ2.5 V, Analog Multiplexers
a
ADG725/ADG731
FEATURES
FUNCTIONAL BLOCK DIAGRAM
3-Wire SPI Compatible Serial Interface
1.8 V to 5.5 V Single Supply
ꢁ2.5 V Dual-Supply Operation
4 ꢀ On Resistance
0.5 ꢀ On Resistance Flatness
7 mm x 7 mm 48-Lead Chip Scale Package (LFCSP)
or 48-Lead TQFP Package
ADG731
ADG725
S1
S1A
DA
DB
S16A
D
Rail-to-Rail Operation
Power-On Reset
S1B
42 ns Switching Times
S32
S16B
Single 32-to-1 Channel Multiplexer
Dual/Differential 16-to-1 Channel Multiplexer
TTL/CMOS Compatible Inputs
For Functionally Equivalent Devices with Parallel
Interface, See ADG726/ADG732
INPUT SHIFT
REGISTER
INPUT SHIFT
REGISTER
SCLK DIN
SCLK DIN
SYNC
SYNC
APPLICATIONS
Optical Applications
Data Acquisition Systems
Communication Systems
Relay Replacement
Audio and Video Switching
Battery-Powered Systems
Medical Instrumentation
Automatic Test Equipment
GENERAL DESCRIPTION
These parts can operate equally well as either multiplexers or
demultiplexers and have an input signal range that extends to the
supplies. In the OFF condition, signal levels up to the supplies
are blocked. All channels exhibit break-before-make switching
action, preventing momentary shorting when switching channels.
The ADG731/ADG725 are monolithic, CMOS, 32-channel/
dual 16-channel analog multiplexers with a serially controlled
3-wire interface. The ADG731 switches one of 32 inputs
(S1–S32) to a common output, D. The ADG725 can be config-
ured as a dual mux switching one of 16 inputs to one output, or a
differential mux switching one of 16 inputs to a differential output.
The ADG731 and ADG725 are serially controlled 32-channel,
and dual/differential 16-channel multiplexers, respectively. They
are available in either a 48-lead LFCSP or TQFP package.
These mulitplexers utilize a 3-wire serial interface that is com-
patible with SPI®, QSPI™, MICROWIRE™, and some DSP
interface standards. On power-up, the Internal Shift Register
contains all zeros and all switches are in the OFF state.
PRODUCT HIGHLIGHTS
1. 3-Wire Serial Interface.
These multiplexers are designed on an enhanced submicron
process that provides low power dissipation yet gives high switch-
ing speed with very low on resistance and leakage currents.
They operate from a single supply of 1.8 V to 5.5 V or a
±2.5 V dual supply, making them ideally suited to a variety of
applications. On resistance is in the region of a few ohms, is
closely matched between switches, and is very flat over the full
signal range.
2. 1.8 V to 5.5 V Single-Supply or ±2.5 V Dual-Supply
Operation. These parts are specified and guaranteed
with 5 V ±10%, 3 V ±10% single-supply,
and ±2.5 V ±10% dual-supply rails.
3. On Resistance of 4 W.
4. Guaranteed Break-Before-Make Switching Action.
5. 7 mm ¥ 7 mm 48-Lead Chip Scale Package (LFCSP) or
48-Lead TQFP Package.
Rev. B
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2015 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com