AD9985
ACTIVITY
DETECT
SYNC STRIPPER
SYNC SEPARATOR
INTEGRATOR
NEGATIVE PEAK
CLAMP
COMP
SYNC
VSYNC
1/S
SOG
MUX 1
HSYNC IN
SOG OUT
PLL
ACTIVITY
DETECT
POLARITY
DETECT
HSYNC OUT
PIXEL CLOCK
HSYNC
HSYNC OUT
CLOCK
GENERATOR
MUX 2
MUX 3
COAST
COAST
POLARITY
DETECT
AD9985
VSYNC IN
VSYNC OUT
ACTIVITY
DETECT
POLARITY
DETECT
MUX 4
Figure 14. Sync Processing Block Diagram
Table 43. Control of the Sync Block Muxes via the Serial Register
Serial Bus
Control Bit
0EH: Bit 3
Control
Bit State
Mux No.
Result
Pass Hsync
Pass Sync-on-Green
Pass Coast
Pass Vsync
Pass Vsync
1 and 2
0
1
0
1
0
1
3
ꢀ
0FH: Bit 5
0EH: Bit 0
Pass Sync Separator Signal
SYNC SLICER
up when Hsync pulses are present. But since Hsync pulses are
relatively short in width, the counter only reaches a value of N
before the pulse ends. It then starts counting down, eventually
reaching 0 before the next Hsync pulse arrives. The specific
value of N will vary for different video modes, but will always
be less than 255. For example, with a 1 µs width Hsync, the
counter will only reach 5 (1 µs/200 ns = 5). When Vsync is
present on the composite sync, the counter will also count up.
However, since the Vsync signal is much longer, it will count to
a higher number M. For most video modes, M will be at least
255. So, Vsync can be detected on the composite sync signal by
detecting when the counter counts to higher than N. The
specific count that triggers detection (T) can be programmed
through the serial register (11H).
The purpose of the sync slicer is to extract the sync signal from
the Green graphics channel. A sync signal is not present on all
graphics systems, only those with Sync-on-Green. The sync
signal is extracted from the Green channel in a two-step
process. First, the SOG input is clamped to its negative peak
(typically 0.3 V below the black level). Next, the signal goes to a
comparator with a variable trigger level, nominally 0.15 V above
the clamped level. The “sliced” sync is typically a composite sync
signal containing both Hsync and Vsync.
SYNC SEPARATOR
A sync separator extracts the Vsync signal from a composite
sync signal. It does this through a low-pass filter-like or
integrator-like operation. It works on the idea that the Vsync
signal stays active for a much longer time than the Hsync signal,
so it rejects any signal shorter than a threshold value, which is
somewhere between an Hsync pulsewidth and a Vsync
pulsewidth.
Once Vsync has been detected, there is a similar process to
detect when it goes inactive. At detection, the counter first resets
to 0, then starts counting up when Vsync goes away. Similar to
the previous case, it will detect the absence of Vsync when the
counter reaches the threshold count (T). In this way, it will
reject noise and/or serration pulses. Once Vsync is detected to
be absent, the counter resets to 0 and begins the cycle again.
The sync separator on the AD9985 is simply an 8-bit digital
counter with a 5 MHz clock. It works independently of the
polarity of the composite sync signal. (Polarities are determined
elsewhere on the chip.) The basic idea is that the counter counts
Rev. 0 | Page 28 of 32
5秒后页面跳转
资料手册解读：UC3842参数和管脚说明
一文带你了解无源晶振的负载电容为何要加两颗谐振电容CL1和CL2
玻璃管保险丝与陶瓷管保险丝：区别与替代性探讨
PCF8574资料解读：主要参数分析、引脚说明
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
