5秒后页面跳转
ACT4303YH-T PDF预览

ACT4303YH-T

更新时间: 2022-04-13 02:36:12
品牌 Logo 应用领域
技领 - ACTIVE-SEMI 转换器传感器
页数 文件大小 规格书
15页 622K
描述
30V/3A Sensorless CC/CV Step-Down DC/DC Converter

ACT4303YH-T 数据手册

 浏览型号ACT4303YH-T的Datasheet PDF文件第4页浏览型号ACT4303YH-T的Datasheet PDF文件第5页浏览型号ACT4303YH-T的Datasheet PDF文件第6页浏览型号ACT4303YH-T的Datasheet PDF文件第8页浏览型号ACT4303YH-T的Datasheet PDF文件第9页浏览型号ACT4303YH-T的Datasheet PDF文件第10页 
ACT4303  
Active- Semi  
Rev 0, 05-Dec-11  
APPLICATIONS INFORMATION CONT’D  
The selected inductor should not saturate at ILPK.  
The maximum output current is calculated as:  
Output Capacitor  
The output capacitor also needs to have low ESR to  
keep low output voltage ripple. The output ripple  
voltage is:  
1
_
IOUTMAX = ILIM  
ILPK _  
PK  
(5)  
2
VIN  
+
VRIPPLE = IOUTMAXKRIPPLERESR  
(6)  
28 × fSW 2 LCOUT  
LLIM is the internal current limit, which is typically  
3.2A, as shown in Electrical Characteristics Table.  
Where IOUTMAX is the maximum output current,  
KRIPPLE is the ripple factor, RESR is the ESR of the  
output capacitor, fSW is the switching frequency, L is  
the inductor value, and COUT is the output  
capacitance. In the case of ceramic output  
capacitors, RESR is very small and does not  
External High Voltage Bias Diode  
It is recommended that an external High Voltage  
Bias diode be added when the system has a 5V  
fixed input or the power supply generates a 5V  
output. This helps improve the efficiency of the  
regulator. The High Voltage Bias diode can be a  
low cost one such as IN4148 or BAT54.  
contribute to the ripple. Therefore,  
a
lower  
capacitance value can be used for ceramic type. In  
the case of tantalum or electrolytic capacitors, the  
ripple is dominated by RESR multiplied by the ripple  
current. In that case, the output capacitor is chosen  
to have sufficiently low ESR.  
Figure 4:  
External High Voltage Bias Diode  
For ceramic output capacitor, typically choose a  
capacitance of about 22µF. For tantalum or  
electrolytic capacitors, choose a capacitor with less  
than 50mESR.  
Rectifier Diode  
Use a Schottky diode as the rectifier to conduct  
current when the High-Side Power Switch is off.  
The Schottky diode must have current rating higher  
than the maximum output current and a reverse  
voltage rating higher than the maximum input  
voltage.  
This diode is also recmended for high duty cycle  
operation and high out voltage applications.  
Input Capacitor  
The input capacitor needs to be carefully selected  
to maintain sufficiently low ripple at the supply input  
of the converter. A low ESR capacitor is highly  
recommended. Since large current flows in and out  
of this capacitor during switching, its ESR also  
affects efficiency.  
The input capacitance needs to be higher than  
10µF. The best choice is the ceramic type,  
however, low ESR tantalum or electrolytic types  
may also be used provided that the RMS ripple  
current rating is higher than 50% of the output  
current. The input capacitor should be placed close  
to the IN and G pins of the IC, with the shortest  
traces possible. In the case of tantalum or  
electrolytic types, they can be further away if a  
small parallel 0.1µF ceramic capacitor is placed  
right next to the IC.  
Innovative PowerTM  
- 7 -  
www.active-semi.com  
Copyright © 2011 Active-Semi, Inc.  

与ACT4303YH-T相关器件

型号 品牌 描述 获取价格 数据表
ACT4402 AEROFLEX ACT4402 SINGLE TRANSCEIVER FOR MIL-STD-1553/1760

获取价格

ACT4402-I AEROFLEX ACT4402 SINGLE TRANSCEIVER FOR MIL-STD-1553/1760

获取价格

ACT4404N AEROFLEX Single Transceiver for MACAIR (A3818, A4905, A5232, A5690), MIL-STD-1553 & SAE-AS15531

获取价格

ACT4404N_07 AEROFLEX Single Transceiver for MACAIR (A3818, A4905, A5232, A5690), MIL-STD-1553 & SAE-AS15531

获取价格

ACT4404N-2 AEROFLEX Single Transceiver for MACAIR (A3818, A4905, A5232, A5690), MIL-STD-1553 & SAE-AS15531

获取价格

ACT4407N AEROFLEX Single Transceiver for MACAIR (A3818, A4905, A5232, A5690), MIL-STD-1553 & SAE-AS15531

获取价格