5秒后页面跳转
A25S16M8VR-X PDF预览

A25S16M8VR-X

更新时间: 2022-02-26 12:26:39
品牌 Logo 应用领域
创瑞 - AITSEMI /
页数 文件大小 规格书
52页 2819K
描述
MEMORY 16M BIT SPI NOR FLASH

A25S16M8VR-X 数据手册

 浏览型号A25S16M8VR-X的Datasheet PDF文件第46页浏览型号A25S16M8VR-X的Datasheet PDF文件第47页浏览型号A25S16M8VR-X的Datasheet PDF文件第48页浏览型号A25S16M8VR-X的Datasheet PDF文件第50页浏览型号A25S16M8VR-X的Datasheet PDF文件第51页浏览型号A25S16M8VR-X的Datasheet PDF文件第52页 
A25S16  
MEMORY  
AiT Semiconductor Inc.  
www.ait-ic.com  
16M BIT SPI NOR FLASH  
6.  
Erase / Program Suspend (75H)  
The Erase/Program Suspend instruction allows the system to interrupt a Sector or Block Erase operation,  
then read from or program data to any other sector. The Erase/Program Suspend instruction also allows the  
system to interrupt a Page Program operation and then read from any other page or erase any other sector or  
block. The Erase/Program Suspend instruction sequence is shown in Figure 34.  
The Write Status Registers instruction (01h) and Erase instructions (20h, D8h, C7h, 60h, 44h) are not allowed  
during Erase Suspend. Erase Suspend is valid only during the Sector or Block erase operation. If written  
during the Chip Erase operation, the Erase Suspend instruction is ignored. The Write Status Registers  
instruction (01h), and Program instructions (02h, 32h, 42h) are not allowed during Program Suspend.  
Program Suspend is valid only during the Page Program operation.  
Figure 34. Erase/Program Suspend Command Sequence  
7.  
Erase / Program Resume (7AH)  
The Erase/Program Resume instruction “7Ah” must be written to resume the Sector or Block Erase operation  
or the Page Program operation after an Erase/Program Suspend. The Resume instruction “7Ah” will be  
accepted by the device only if the SUS bit in the Status Register equals to 1 and the WIP bit equals to 0.  
After the Resume instruction is issued the SUS bit will be cleared from 1 to 0 immediately, the WIP bit will be  
set from 0 to 1 within 200 ns and the Sector or Block will complete the erase operation or the page will  
complete the program operation. If the SUS bit equals to 0 or the WIP bit equals to 1, the Resume instruction  
“7Ah” will be ignored by the device. The Erase/Program Resume instruction sequence is shown in Figure 35.  
Figure 35. Erase/Program Resume Command Sequence  
REV1.0  
- JUN 2015 RELEASED -  
- 49 -  

与A25S16M8VR-X相关器件

型号 品牌 获取价格 描述 数据表
A2-5S-2.54C HRS

获取价格

Board Connector, 5 Contact(s), 1 Row(s), Female, 0.1 inch Pitch, Crimp Terminal, Locking,
A2-5S-2.54F HRS

获取价格

Card Edge Connector, 5 Contact(s), 1 Row(s), Female, IDC Terminal, Socket
A25S40 AITSEMI

获取价格

MEMORY 4M BIT SPI NOR FLASH
A25S40M8R-X AITSEMI

获取价格

MEMORY 4M BIT SPI NOR FLASH
A25S40M8VR-X AITSEMI

获取价格

MEMORY 4M BIT SPI NOR FLASH
A25S80 AITSEMI

获取价格

MEMORY 8M BIT SPI NOR FLASH
A25S80M8R-X AITSEMI

获取价格

MEMORY 8M BIT SPI NOR FLASH
A25S80M8VR-X AITSEMI

获取价格

MEMORY 8M BIT SPI NOR FLASH
A25X ETC

获取价格

SEMICONDUCTOR PROTECTION FUSES
A25X1000-128 ETC

获取价格

SEMICONDUCTOR PROTECTION FUSES