93LC56A/B
TABLE 1-1
Name
PIN FUNCTION TABLE
Function
1.0
ELECTRICAL
CHARACTERISTICS
CS
CLK
DI
Chip Select
1.1
Maximum Ratings*
Serial Data Clock
Serial Data Input
Serial Data Output
Ground
VCC...................................................................................7.0V
All inputs and outputs w.r.t. Vss ................ -0.6V to Vcc +1.0V
Storage temperature .....................................-65°C to +150°C
Ambient temp. with power applied.................-65°C to +125°C
Soldering temperature of leads (10 seconds) .............+300°C
ESD protection on all pins................................................4 kV
DO
VSS
NC
VCC
No Connect
Power Supply
*Notice: Stresses above those listed under “Maximum ratings” may
cause permanent damage to the device.This is a stress rating only and
functional operation of the device at those or any other conditions
above those indicated in the operational listings of this specification is
not implied. Exposure to maximum rating conditions for extended peri-
ods may affect device reliability.
TABLE 1-2
DC AND AC ELECTRICAL CHARACTERISTICS
All parameters apply over the specified Commercial (C): VCC = +2.5V to +6.0V
Tamb = 0°C to +70°C
operating ranges unless otherwise
noted
Industrial (I):
VCC = +2.5V to +6.0V
Tamb = -40°C to +85°C
Parameter
Symbol
Min.
Max.
Units
Conditions
2.7V ≤ VCC ≤ 5.5V (Note 2)
VIH1
VIH2
VIL1
VIL2
VOL1
VOL2
VOH1
VOH2
ILI
2.0
0.7 Vcc
-0.3
-0.3
—
Vcc +1
Vcc +1
0.8
V
V
High level input voltage
VCC < 2.7V
V
VCC > 2.7V (Note 2)
VCC < 2.7V
Low level input voltage
Low level output voltage
High level output voltage
0.2 Vcc
0.4
V
V
IOL = 2.1 mA; Vcc = 4.5V
IOL =100 µA; Vcc = Vcc Min.
IOH = -400 µA; Vcc = 4.5V
IOH = -100 µA; Vcc = Vcc Min.
VIN = VSS
—
0.2
V
2.4
—
V
Vcc-0.2
-10
—
V
Input leakage current
Output leakage current
10
µA
µA
ILO
-10
10
VOUT = VSS
Pin capacitance
(all inputs/outputs)
VIN/VOUT = 0 V (Notes 1 & 2)
Tamb = +25°C, Fclk = 1 MHz
CIN, COUT
ICC read
—
—
7
pF
1
500
mA
µA
FCLK = 2 MHz; VCC = 6.0V
FCLK = 1 MHz; VCC = 3.0V
Operating current
ICC write
ICCS
—
—
1.5
1
mA
Standby current
Clock frequency
µA
CS = VSS
2
1
MHz
MHz
VCC > 4.5V
VCC < 4.5V
FCLK
—
Clock high time
TCKH
TCKL
TCSS
TCSH
TCSL
TDIS
TDIH
TPD
250
250
50
—
—
ns
ns
Clock low time
Chip select setup time
Chip select hold time
Chip select low time
Data input setup time
Data input hold time
Data output delay time
Data output disable time
Status valid time
—
ns
Relative to CLK
Relative to CLK
0
—
ns
250
100
100
—
—
ns
—
ns
Relative to CLK
—
ns
Relative to CLK
400
100
500
6
ns
Cl = 100 pF
TCZ
—
ns
Cl = 100 pF (Note 2)
Cl = 100 pF
TSV
—
ns
TWC
TEC
—
ms
ms
ms
cycles
ERASE/WRITE mode
ERAL mode
Program cycle time
Endurance
—
6
TWL
—
—
15
—
WRAL mode
1M
25°C, VCC = 5.0V, Block Mode (Note 3)
Note 1: This parameter is tested at Tamb = 25°C and FCLK = 1 MHz.
2: This parameter is periodically sampled and not 100% tested.
3: This application is not tested but guaranteed by characterization. For endurance estimates in a specific application, please consult the Total
Endurance Model which may be obtained on Microchip’s BBS or website.
DS21208A-page 2
Preliminary
1997 Microchip Technology Inc.