8XC152JA/JB/JC/JD
Pin Description (Continued)
Pin Description
Ý
Pin
47-40
65-58
Port 4ÐPort 4 is an 8-bit bidirectional I/O port with internal pullups. Port 4 pins that
have 1s written to them are pulled high by the internal pullups, and in that state can
be used as inputs. As inputs, Port 4 pins that are externally being pulled low will
source current (I , on the data sheet) because of the internal pullups. In addition,
IL
Port 4 also receives the low-order address bytes during program verification.
9
13
55
RSTÐReset input. A logic low on this pin for three machine cycles while the
oscillator is running resets the device. An internal pullup resistor permits a power-on
reset to be generated using only an external capacitor to V . Although the GSC
SS
recognizes the reset after three machine cycles, data may continue to be
transmitted for up to 4 machine cycles after Reset is first applied.
38
ALEÐAddress Latch Enable output signal for latching the low byte of the address
during accesses to external memory.
In normal operation ALE is emitted at a constant rate of (/6 the oscillator
frequency, and may be used for external timing or clocking purposes. Note,
however, that one ALE pulse is skipped during each access to external Data
Memory. While in Reset, ALE remains at a constant high level.
37
54
56
PSENÐProgram Store Enable is the Read strobe to External Program Memory.
When the 8XC152 is executing from external program memory, PSEN is active
(low). When the device is executing code from External Program Memory, PSEN is
activated twice each machine cycle, except that two PSEN activations are skipped
during each access to External Data Memory. While in Reset, PSEN remains at a
constant high level.
39
23
EAÐExternal Access enable. EA must be externally pulled low in order to enable
the 8XC152 to fetch code from External Program Memory locations 0000H to
0FFFH.
EA must be connected to V for internal program execution.
CC
32
31
XTAL1ÐInput to the inverting oscillator amplifier and input to the internal clock
generating circuits.
22
XTAL2ÐOutput from the inverting oscillator amplifier.
N/A
17, 20
21, 22
38, 39
40, 49
Port 5ÐPort 5 is an 8-bit bidirectional I/O port with internal pullups. Port 5 pins that
have 1s written to them are pulled high by the internal pullups, and in that state can
be used as inputs. As inputs, Port 5 pins that are externally being pulled low will
source current (I , on the data sheet) because of the internal pullups.
IL
Port 5 is also the multiplexed low-order address and data bus during accesses to
external program memory if EBEN is pulled high. In this application it uses strong
pullups when emitting 1s.
N/A
67, 66
52, 57
50, 68
1, 51
Port 6ÐPort 6 is an 8-bit bidirectional I/O port with internal pullups. Port 6 pins that
have 1s written to them are pulled high by the internal pullups, and in that state can
be used as inputs. As inputs, Port 6 pins that are externally pulled low will source
current (I , on the data sheet) because of the internal pullups.
IL
Port 6 emits the high-order address byte during fetches from external Program
Memory if EBEN is pulled high. In this application it uses strong pullups when
emitting 1s.
N/A
N/A
12
53
EBENÐE-Bus Enable input that designates whether program memory fetches take
place via Ports 0 and 2 or Ports 5 and 6. Table 1 shows how the ports are used in
conjunction with EBEN.
EPSENÐE-bus Program Store Enable is the Read strobe to external program
memory when EBEN is high. Table 2 shows when EPSEN is used relative to PSEN
depending on the status of EBEN and EA.
6
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
