Datasheet > 543400-1

543400-1

更新时间： 2024-11-22 01:09:55

品牌	Logo	应用领域
泰科 - TE		/
页数	文件大小	规格书
4页	175K
描述
This instruction sheet covers the use and maintenance of Crimping Die Assemblies

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

543400-1 数据手册

Instruction Sheet

Crimping Die Assemblies 1583015-1,

-2, -3, and 1583016-1 for High Speed

Serial Data Connector 2 (HSSDC2)

408-8609

19 DEC 11 Rev A

The ferrule, which is ordered separately from the

AMPLIMITE* connector, is sized according to the

insulation diameter of the cable. Each die assembly is

marked with the cable insulation diameter range.

3. DIE ASSEMBLY INSTALLATION

The die assembly is designed to fit securely into the

tool by upper and lower die holder plates; each die is

held in by a single screw. To install the die assembly,

refer to the instructions packaged with the tool:

408-9315 Hand Crimping Tool Frame Assembly

543344-1

408-9245 Hand Crimping Tool Frame Assembly

58235-1

408-9721 Die Holder Assembly 58449-1

409-5822 Pneumatic Power Unit 312522-3

4. CRIMPING PROCEDURE

Assemble the connector. Make sure the ferrule is over

the connector shield cable outlet and butted against

the shield body. Then, proceed as follows:

1. Place the ferrule on the moving die, with the

cable extending out the back side of the die. Make

sure that the front part of the ferrule is positioned in

the braid section and the back part of the ferrule is

positioned in the insulation section. See Figure 2.

Figure 1

1. INTRODUCTION

This instruction sheet covers the use and maintenance

of Crimping Die Assemblies 1583015-1, -2, -3, and

1583016-1, which are designed to be used in Hand

Crimping Tool Frame Assembly 543344-1 or 58235-1,

or in Pneumatic Power Unit 312522-3 equipped with

Die Holder Assembly 58449-1. Each die assembly

crimps a ferrule onto round shielded cable used with

HSSDC2 Connectors.

The front edge of the ferrule must be against the

stop and the connector body must be clear of the

CAUTION

dies.

2. Actuate tool for crimping according to the

instructions packaged with the tool.

Reason for revision is given in Section 7, REVISON

SUMMARY.

3. Remove connector from die assembly and

inspect the crimped ferrule to the requirements

outlined in the applicable application specification:

Dimensions are in millimeters [with inches in

brackets]. Figures and illustrations are for

NOTE

114-13028 High Speed Serial Data

Connector 2 (HSSDC2)

reference only and are not drawn to scale.

See Figure 3 for a properly crimped ferrule.

2. DESCRIPTION

5. MAINTENANCE AND INSPECTION PROCEDURE

Each die assembly consists of an indenter (stationary

die) and an anvil (moving die). When mated, the dies

form two crimping sections: the braid and the

insulation. The braid section crimps the front part of

the ferrule onto the cable shield and the cable outlet of

the connector shield assembly, and simultaneously,

the insulation section crimps the back part of the

ferrule onto the cable insulation. The anvil die is

designed with a stop to ensure proper positioning of

the ferrule for crimping. See Figure 1.

The die assembly is inspected prior to shipment,

however, it is recommended that the die assembly be

inspected immediately upon arrival. TE Connectivity

recommends that a maintenance and inspection

program be performed periodically to ensure

continued reliability of the die assembly. The

inspection frequency should be based on the amount

of use, working conditions, operator training and skill,

and established company standards.

1 of 4

*Trademark

PRODUCT INFORMATION 1-800-522-6752

For latest revision and Regional Customer Service,

visit our website at www.te.com

LOC B

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

12 3 4

中文翻译

下载PDF

与543400-1相关器件

型号	品牌	获取价格	描述	数据表
5434010	PHOENIX	获取价格	Printed-circuit board connector - BCH-508V-14 GY
5434023	PHOENIX	获取价格	TERM BLOCK HDR 15POS VERT 5.08MM
5434036	PHOENIX	获取价格	TERM BLOCK HDR 16POS VERT 5.08MM
5434049	PHOENIX	获取价格	TERM BLOCK HDR 17POS VERT 5.08MM
5434052	PHOENIX	获取价格	TERM BLOCK HDR 18POS VERT 5.08MM
543407-1	TE	获取价格	This instruction sheet covers the use and maintenance of Crimping Die Assemblies
5434078	PHOENIX	获取价格	TERM BLOCK HDR 20POS VERT 5.08MM
5434081	PHOENIX	获取价格	TERM BLOCK HDR 21POS VERT 5.08MM
543408-1	TE	获取价格	This instruction sheet covers the use and maintenance of Crimping Die Assemblies
543409-1	TE	获取价格	This instruction sheet covers the use and maintenance of Crimping Die Assemblies

与543400-1相关文章

解析光耦仿真器：升级光耦合器技术的必要性
2024-11-18

27
英伟达新一代Blackwell GPU过热问题致交付延迟
2024-11-18

19
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
2024-11-14

49
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
2024-11-14

47

产品中心

服务支持

精选活动

关于我们

帮助中心

543400-1

543400-1 数据手册

与543400-1相关器件

与543400-1相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

543400-1

543400-1 数据手册

与543400-1相关器件

与543400-1相关文章

您还可以找

您在本页遇到什么问题？