Signal Relays
AXICOM
P2 Relay V23079
n
n
n
n
n
n
n
Standard telecom relay (ringing and test access)
Slim line 15x7.5mm (.590x.295”)
Max. switching current 5A
2 form C bifurcated contacts (2 changeover contacts, 2 CO)
Immersion cleanable
High sensitivity for low power consumption 140mW/ 70mW
Single coil version with surge voltage resistance between contact
and coil: 2.5kV (2/10μs) meets the Telcordia Requirement GR-1089,
1.5kV (10/160μs) meets FCC Part 68
Typical applications
Communications equipment linecard application (ringing and test access),
PABX, voice over IP, office equipment, measurement and control equipment,
automotive equipment as CAN bus, keyless entry, speaker switch, medical
equipment, consumer electronics, set top boxes, HiFi
Z
Approvals
UL 508 File No. E 111441, UL 60950,
IEC/EN60950 IEC Ref. Cert. No. 327
Technical data of approved types on request
Coil Data
Magnetic system
Coil voltage range
Max. coil temperature
Thermal resistance
polarized
2 to 24VDC
125°C
< 125K/W
Contact Data
Contact arrangement
Max. switching voltage
Rated current
2 form C (CO)
220VDC, 250VAC
2A
Coil versions, monostable
Coil
code
Rated
voltage
VDC
3.00
4.00
4.50
5.00
6.00
9.00
Operate Limiting Release
Coil
Rated coil
voltage
VDC
2.25
3.00
3.38
3.75
4.50
6.75
9.00
18.00
Voltage
VDC
6.50
8.70
9.80
10.90
13.00
19.60
26.15
52.30
voltage resistance power
Limiting continuous current, 85°C
Switching Power
Contact material
2A
VDC
0.30
0.40
0.45
0.50
0.60
0.90
1.20
2.40
Ω 10ꢀ
64
114
145
178
257
578
1029
4114
mW
140
140
140
140
140
140
140
140
60W, 62.5VA
AgNi, gold-covered
bifurcated contact
100μV
008
016
011
001
002
006
003
005
Contact style
Minimum switching voltage
Thermoelectrical potential
Initial contact resistance
Frequency of operation, without load
Operate time
Set/reset time
Release time
<10µV
<50mΩ at 10mA, 20mV
50 operations/s
typ. 2ms, max. 4ms
typ. 2ms, max. 4ms
12.00
24.00
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Other coil voltages on request.
without diode in parallel
with diode in parallel
Bounce time
Electrical endurance
at 12V / 10mA
at 6V / 100mA
at 60V / 500mA
at 30V / 1000mA
at 30V / 2000mA
Contact ratings, UL
typ. 2ms, max. 4ms
typ. 4ms, max. 6ms
typ. 1ms, max. 3ms
2.8
140 mW
2.6
Umax. at 0 A
Umax. at 2 x 1 A
Umax. at 2 x 2 A
2.4
typ. 5x107 operations
typ. 1x107 operations
typ. 5x105 operations
typ. 1x106 operations
typ. 2x105 operations
110VDC / 0.3A - 33W
30VDC / 2.0A - 60W
120VAC / 0.5A - 60VA
240VAC / 0.25A -60VA
typ. 100x106 operations
2.2
2
1.8
1.6
1.4
1.2
Unom. nominal coil voltage
1
0.8
0.6
Uop. min.
Urel. min.
0.4
Mechanical endurance
0.2
0
Max. DC load breaking capacity
-40 -30 -20 -10
0
10 20 30 40 50 60 70 80 90 100 110 120 130 140
Ambient Temperature [°C]
DC current [A]
1
07-2015, Rev.0715
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
www.te.com
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
© 2015 Tyco Electronics Corporation,
a TE Connectivity Ltd. company