Instruction Sheet
Pneumatic CERTI-CRIMP* Tool Holder
Assemblies 356302-1, 356303-1, and 1673611-1
(For Use w/ Pneumatic Tooling Assemblies)
408-4303
11 MAR 10 Rev F
3. INSTALLATION
Cam
Tool Holder
Body
Previously installed cams and tool holders must
be removed before installing different ones.
NOTE
Ratchet
Pawl
i
Adjustable
Eccentric
Air pressure must be removed from the tool while
head or tool holder is detached.
DANGER
If the piston is not extended, it must first be
extended to allow installation of the cam. To
extend the piston, firmly grasp the piston with
piston pliers and pull away from the body of the
tool. Piston pliers are provided with the power
unit.
DANGER
Securing Screw
(3 Places)
Pivot Pin
Tool Holder 356303-1
A strip of adhesive--backed safety labels, printed in
various languages, is packaged with the tool holder
assembly. Remove the appropriate language label
from the strip and attach it to the tool holder or safety
sleeve. The safety sleeve is supplied with the small
and large tool holder assemblies. For these
assemblies, attach the safety labels to the safety
sleeve.
Figure 1
1. INTRODUCTION
Pneumatic CERTI--CRIMP Tool Holder Assemblies
356302--1 and 356303--1 are used with Pneumatic
Tooling Assemblies 189721--1 or 189722--1.
Pneumatic CERTI--CRIMP Tool Holder Assembly
1673611--1 is used with Pneumatic Tooling Assembly
1490567--1.
Be sure to select the correct assembly of tool
holder and cam. If incorrect assembly is used,
system will not operate properly.
CAUTION
!
The tool holders are designed to accept
interchangeable crimping heads for crimping various
types of connectors.
1. If cam setscrew is not installed in cam, thread
setscrew into cam two to three turns.
2. Place cam (with setscrew) onto piston rod. The
cam should butt against the piston rod face. If not,
turn cam setscrew counterclockwise until cam fits
on piston rod properly.
For information concerning setup and operation of the
pneumatic tools, refer to Customer Manual 409--5862.
Read these instructions thoroughly before using the
tool holder.
Overtightening the cam setscrew may damage
the setscrew or cam.
CAUTION
Measurements are in metric units [with U.S.
customary units in brackets]. Figures and
illustrations are for reference only and are not
drawn to scale.
NOTE
!
i
3. Tighten cam setscrew, then pull on cam to
ensure that it is firmly attached.
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
4. Properly align tool holder ratchet pawl with the
cam teeth (shown in Figure 2) and push tool holder
onto power unit so that it passes over the friction
ring on the power unit piston.
2. DESCRIPTION (Figure 1)
The tool holder assembly consists of the tool holder
body, cam, adjustable eccentric, pivot pin, and ratchet
pawl with emergency release. The ratchet ensures
that the tool completes the crimp cycle.
5. Slide tool holder locking ring toward tool holder
until it butts against the stop ring on the power unit
piston. Then turn ring clockwise to engage threads
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
E2010 Tyco Electronics Corporation, Berwyn, PA
1 of 4
All Rights Reserved
TE logo and Tyco Electronics are trademarks.
LOC B
*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
