Datasheet > 314078-2

314078-2

更新时间： 2024-12-02 00:58:19

品牌	Logo	应用领域
泰科 - TE		/
页数	文件大小	规格书
4页	165K
描述
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools.

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

314078-2 数据手册

Instruction Sheet

Interchangeable Crimping Dies 58373-1 and 58374-1 

(Used in Hand Crimping Tool 69710-1 and 

Pneumatic Tools 69365, 69365-2, and 69365-3)

408-9442

06 DEC 11 Rev B

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use

and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

holding screw. The stationary die is secured to the

stationary die holder located in the upper portion of the

tool head.

Stationary Die

Wire

Range

Marking

3. DIE INSTALLATION

If using the hand tool, follow the die installation steps

in Paragraph 3.1; if using any of the pneumatic tools,

follow the die installation steps in Paragraph 3.2.

3.1. Hand Tool

1. Position stationary die in stationary die holder

and moving die in moving die holder. See Figure 3.

Fasten die holding screws enough to hold dies in

place but do NOT tighten fully.

Locator /

Insulation

Stop

Die

Holding

Screws

2. Close handles until the dies bottom. Then tighten

both holding screws. The tool can now be used to

crimp the contacts to wires.

Check die alignment and tighten die 

NOTE

holding screws.



Moving Die

Figure 1

1. INTRODUCTION

Insulation Barrel

Stabilizer

Interchangeable Crimping Die Assemblies 58373-1

and 58374-1 (see Figure 1) are designed to be used in

Hand Crimping Tool 69710-1 and Pneumatic Tools

69365, 69365-2, and 69365-3 to crimp .140 MATE-N-

LOK* loose piece pin and socket contacts listed in

Figure 2. Die set 58373-1 crimps No. 10 AWG wires

and die set 58374-1 crimps 14-12 AWG wires. Read

these instructions thoroughly before starting.

Wire Barrel

Socket

Wire

Strip

Length

†

Measurements are in millimeters [followed by 

Locator Slot

NOTE

NOTE: Not to Scale

inch equivalents in brackets]. Figures and

†

illustrations are for identification only and are 

not drawn to scale.

If insulation diameter range is 2.54-3.78 [.100-.149], wire strip

length is 6.35 [.250]; if insulation diameter range is 3.81-4.06

[.150 to .160], wire strip length is 7.92 [.312].

Reasons for reissue are provided in Section 7,

REVISION SUMMARY.

CONTACT PART

CRIMP

CRIMPING WIRE

DIE PART SIZE

NUMBER (AWG)

NUMBER

INSULDIA

SECT

2. DESCRIPTION

†

WIRE SIZE

MARKING

RANGE

LOOSE

PIECE

STRIP

Each crimping die assembly consists of a moving die

and a stationary die, as shown in Figure 1. The

moving die is positioned in the lower portion of the tool

head and is attached to the moving die holder by a die

58374-1

58373-1

14-12

2.54-4.06

[.100-.160]

350200 350390

350201 350391

Figure 2

*Trademark



This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

1 of 4

PRODUCT INFORMATION 1-800-522-6752

LOC B

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

12 3 4

中文翻译

下载PDF

与314078-2相关器件

型号	品牌	获取价格	描述	数据表
314079-1	TE	获取价格	Cumulative Trauma Disorders can result from the prolonged use of manually powered hand too
314080-1	TE	获取价格	Cumulative Trauma Disorders can result from the prolonged use of manually powered hand too
31408-1080	MOLEX	获取价格	USCAR 2.54mm (.100”) Pitch Receptacle, 8 Circ
31408-1081	MOLEX	获取价格	USCAR 2.54mm (.100”) Pitch Receptacle, 8 Circ
31408-1082	MOLEX	获取价格	USCAR 2.54mm (.100”) Pitch Receptacle, 8 Circ
314081-1	TE	获取价格	Cumulative Trauma Disorders can result from the prolonged use of manually powered hand too
31408-1121	MOLEX	获取价格	USCAR 2.54mm (.100”) Pitch Receptacle, 12 Cir
31408-1122	MOLEX	获取价格	USCAR 2.54mm (.100”) Pitch Receptacle, 12 Cir
31408-1160	MOLEX	获取价格	USCAR 2.54mm (.100”) Pitch Receptacle
31408-1162	MOLEX	获取价格	USCAR 2.54mm (.100”) Pitch Receptacle, 16 Cir

与314078-2相关文章

解析光耦仿真器：升级光耦合器技术的必要性
2024-11-18

53
英伟达新一代Blackwell GPU过热问题致交付延迟
2024-11-18

42
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
2024-11-14

70
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
2024-11-14

66

产品中心

服务支持

精选活动

关于我们

帮助中心

314078-2

314078-2 数据手册

与314078-2相关器件

与314078-2相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

314078-2

314078-2 数据手册

与314078-2相关器件

与314078-2相关文章

您还可以找

您在本页遇到什么问题？