Thyristors
Surface Mount – 200V-600W > 2N6071A/B Series
Maximum Ratings andThermal Characteristics (TJ = 25°C unless otherwise noted)
Rating
*Peak Repetitive Off-State Voltage (Note 1)
Symbol
Value
Unit
(TJ = -40 to 110°C, Sine Wave, 50 to 60 Hz, Gate Open)
200
400
600
VDRM
,
2N6071A,B
2N6073A,B
2N6075A,B
-
VRRM
*On-State RMS Current (TC = 85°C) Full Cycle Sine Wave 50 to 60 Hz
*Peak Non-repetitive Surge Current (One Full cycle, 60 Hz, TJ = +110°C)
Circuit Fusing Considerations (t = 8.3 ms)
IT(RMS)
ITSM
I2t
4.0
A
A
30
3.7
10
A2s
W
*Peak Gate Power (Pulse Width “1.0 µs, TC = 85°C)
*Average Gate Power (t = 8.3 ms, TC = 85°C)
*Peak Gate Voltage (Pulse Width “1.0 µs, TC = 85°C)
*Operating JunctionTemperature Range
PGM
PG(AV)
VGM
TJ
0.5
W
5.0
V
-40 to +110
-40 to +150
8.0
°C
*StorageTemperature Range
Tstg
_
°C
MountingTorque (6-32 Screw) (Note 2)
in. lb.
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
1. VDRM and VRRM for all types can be applied on a continuous basis. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded.
2. Torque rating applies with use of a compression washer. Mounting torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. Main terminal 2 and heatsink contact pad are common.
Thermal Characteristics
Rating
Symbol
Value
Unit
*Thermal Resistance, Junction to Case
R8JC
R8JA
TL
3.5
75
°C/W
°C/W
°C
Thermal Resistance, Junction to Ambient (Note 1)
Maximum LeadTemperature for Soldering Purposes, 1/8” from case for 10 seconds
260
*Indicates JEDEC Registered Data.
Electrical Characteristics - OFF (TC = 25°C unless otherwise noted; Electricals apply in both directions)
Characteristic
Symbol
Min
Typ
Max
Unit
-
-
-
-
10
2
µA
*Peak Repetitive Blocking CurrentTJ = 25°C (VD = VDRM = VRRM;
Gate Open)TJ = 110°C
TJ = 25°C
TJ = 110°C
IDRM,
IRRM
mA
Electrical Characteristics - ON (TC = 25°C unless otherwise noted; Electricals apply in both directions)
Characteristic
Symbol
C
Min
Typ
-
Max
2
Unit
V
*Peak On-State Voltage (Note 3) (ITM
=
6.0 A Peak)
-
-
*GateTrigger Voltage (Continuous DC), All Quadrants
(MainTerminal Voltage = 12 Vdc, RL = 100 Ω, TJ = -40 °C)
VGT
1.4
2.5
V
Gate Non-Trigger Voltage, All Quadrants
(MainTerminal Voltage = 12 Vdc, RL = 100 Ω, TJ = 110°C)
VGD
.02
-
-
V
-
-
-
-
-
30
15
-
*Holding Current
TJ = -40°C
TJ = 25°C
IH
mA
µs
(MainTerminal Voltage = 12 Vdc, Gate Open, Initiating Current = 1 Adc)
Turn-OnTime (ITM = 14 Adc, IGT = 100 mAdc)
tgt
1.5
QUADRANT
(Maximum Value)
Type
IGT @TJ
I mA
II mA
III mA
IV mA
2N6071A
2N6073A
2N6075A
2N6071B
2N6073B
2N6075B
+25°C
-40°C
+25°C
-40°C
5
20
3
5
20
3
5
20
3
10
30
5
GateTrigger Current (Continuous DC)
(MainTerminal Voltage = 12 Vdc, RL = 100 Ω)
15
15
15
20
3. Pulse Test: Pulse Width ≤ 2.0 ms, Duty Cycle ≤ 2%.
*Indicates JEDEC Registered Data.
© 2020 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 08/24/20