Datasheet > 2-306144-3

2-306144-3

更新时间： 2024-11-28 01:07:31

品牌	Logo	应用领域
MACOM		/
页数	文件大小	规格书
8页	1712K
描述
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools.

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

2-306144-3 数据手册

TERMASHIELD* Ferrule

Crimping Dies

for Tools 59500 and 69270-1

408-1662

26 MAY 10 Rev A

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and

low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

1. Determine the outside (insulation) diameter of

the primary conductor.

1. INTRODUCTION

This instruction sheet is intended to provide you with

instructions” on product application and a

maintenance and for: TERMASHIELD Ferrule

Crimping Dies (Used in Tools 59500 and 69270-1

(Mod. 2):

2. Locate this dimension in the appropriate

primary conductor insulation range in column 2

of Figure 1. Opposite the insulation range you will

find the catalog numbers of the crimping die.

ferrule and insulating cap to use.

Tools

Crimping Dies

45065-3

Crimping dies, ferrules and insulating caps are

color coded. For example: Use dies color coded

45061-3

45062-3

45063-3

45064-3

45240-2

NOTE

green to crimp a green fermle. Place a green insu-

lating cap on the green ferrule after ferrule is

crimped.

45066-3

45241-2

59500

69270-1

45238-2

B. Multiple Conductor Shielded Wire

45239-2

To determine which dies, ferrule and insulating cap to

use with shielded wire having two or more conductors,

use the following formula: Multiply the outside

(insulation) diameter of one primary conductor by the

“factor”, see Figure 2, listed opposite the total number

of conductors in the wire. For example:

TERMASHIELD ferrules on single and multiple

conductor shielded wires with a primary conductor

insulation range of .033" to .270",

Basic instructions on the use of these tools, dies, die

insertion and removal, etc., are provided in Section 2,

1. If you had a 3-conductor shielded wire, you

would first find the outside (insulation) diameter

of one conductor. In this case, we will use an

outer diameter of .082 inches.

'For further instructions relative to the pneumatic tool

and hand tool, refer to the instructions packaged with

these tools.

2. Opposite the number “3” (the number of

primary conductors in the wire) in column one of

Figure 2, you will find a multiplying factor of 2.17.

Section 3 contains a “Maintenance and Inspection

Procedure” which will enable you to establish and

maintain a die certification program.

3. Multiply the outer diameter of the one

conductor (.082 inches) by this factor (2.17). The

result is.177. This figure (.177) is the primary

conductor insulation range of the three-conductor

shielded wire.

These instructions may be used for dies not listed in

Figure 1 but accompanied by this 408 series

document. For unlisted dies, strip wire and crimp in

the same manner as for identical size dies.

2. INSTRUCTIONS

4. Next, refer to column 2 of Figure 1. Opposite

the insulation range of.145 to .184, you will find

the numbers of the crimping die, ferrule and

insulating cap to use.

2.1. Selection Data for Dies, Ferrules, and Insulating

Caps

A. Single Conductor Shielded Wire

2.2. Die Insertion Hand Tool No 59500

To determine which dies, ferrule and insulating cap to

use with single conductor shielded wire, refer to -

Figure 1.

Dies are coated with oil to prevent rust and corrosion.

Wipe this oil from dies, particularly from crimping area.

The package numbers shown in Figure 1 are sup-

plied with equal quantities of ferrules and insulating

caps, but include only zinc plated ferrules.

1. (To open tool handles, close handles until

CERTI-CRIMP* tool ratchet releases. See Figure

3. Note that once ratchet is engaged, handles

cannot be opened until they are fully closed.

NOTE

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.tycoelectronics.com

TOOLING ASSISTANCE CENTER 1-800-722-1111

PRODUCT INFORMATION 1-800-522-6752

1 of 8

TE logo and Tyco Electronics are trademarks

*Trademark. Other products, logos, and company names might be trademarks of their respective owners.

LOC B

12 3 4 5 6 7 8

中文翻译

下载PDF

与2-306144-3相关器件

型号	品牌	获取价格	描述	数据表
2-306144-4	MACOM	获取价格	Cumulative Trauma Disorders can result from the prolonged use of manually powered hand too
2-306144-5	MACOM	获取价格	Cumulative Trauma Disorders can result from the prolonged use of manually powered hand too
2306-15-D2-30-010	ECS	获取价格	Card Edge Connector
2306-15-D2-60-010	ECS	获取价格	Card Edge Connector
230618181052	VISHAY	获取价格	RESISTOR, METAL FILM, 0.4 W, 1 %, 100 ppm, 1050 ohm, THROUGH HOLE MOUNT, AXIAL LEADED, ROH
230618181053	VISHAY	获取价格	RESISTOR, METAL FILM, 0.4 W, 1 %, 100 ppm, 10500 ohm, THROUGH HOLE MOUNT, AXIAL LEADED, RO
230618181074	VISHAY	获取价格	RESISTOR, METAL FILM, 0.4 W, 1 %, 100 ppm, 107000 ohm, THROUGH HOLE MOUNT, AXIAL LEADED, R
230618181101	VISHAY	获取价格	RESISTOR, METAL FILM, 0.4 W, 1 %, 100 ppm, 110 ohm, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS
230618181103	VISHAY	获取价格	RESISTOR, METAL FILM, 0.4 W, 1 %, 100 ppm, 11000 ohm, THROUGH HOLE MOUNT, AXIAL LEADED, RO
230618181108	VISHAY	获取价格	RESISTOR, METAL FILM, 0.4 W, 1 %, 100 ppm, 1.1 ohm, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS

与2-306144-3相关文章

解析光耦仿真器：升级光耦合器技术的必要性
2024-11-18

46
英伟达新一代Blackwell GPU过热问题致交付延迟
2024-11-18

35
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
2024-11-14

64
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
2024-11-14

61

产品中心

服务支持

精选活动

关于我们

帮助中心

2-306144-3

2-306144-3 数据手册

与2-306144-3相关器件

与2-306144-3相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

2-306144-3

2-306144-3 数据手册

与2-306144-3相关器件

与2-306144-3相关文章

您还可以找

您在本页遇到什么问题？