1N3016B thru 1N3051B, e3
1 WATT METAL CASE ZENER DIODES
S C O T T S D A L E D I V I S I O N
*ELECTRICAL CHARACTERISTICS @ 25oC
TYPICAL
TEMP. COEFF.
OF ZENER
VOLTAGE
αVZ
NOMINAL
MAXIMUM
ZENER
CURRENT
IZM
MAXIMUM
REVERSE
LEAKAGE
CURRENT†
ZENER
VOLTAGE
VZ @ IZT
ZENER
TEST
CURRENT
IZT
MAXIMUM ZENER IMPEDANCE
(Note 3)
JEDEC
TYPE
NUMBER
(Note 1)
(Note 2)
(Note 4)
IR
@
VR
ZZT @ IZT
OHMS
3.5
4.0
4.5
5
ZZK
OHMS
700
700
700
@
IZK
Volts
6.8
7.5
8.2
9.1
10
mA
37
34
31
28
mA
1.0
.5
.5
.5
mA
140
125
115
105
95
85
80
74
63
60
52
47
43
40
34
31
28
26
23
21
19
18
17
15
14
μA
150
100
50
25
25
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
Volts
5.2
5.7
6.2
6.9
7.6
8.4
9.1
9.9
%/oC
.040
.045
.048
.050
.055
.060
.065
.065
.070
.070
.075
.075
.080
.080
.085
.085
.085
.085
.090
.090
.090
.090
.090
.090
.090
.090
.090
.090
.090
.095
.095
.095
.095
.095
.095
.100
1N3016B
1N3017B
1N3018B
1N3019B
1N3020B
1N3021B
1N3022B
1N3023B
1N3024B
1N3025B
1N3026B
1N3027B
1N3028B
1N3029B
1N3030B
1N3031B
1N3032B
1N3033B
1N3034B
1N3035B
1N3036B
1N3037B
1N3038B
1N3039B
1N3040B
1N3041B
1N3042B
1N3043B
1N3044B
1N3045B
1N3046B
1N3047B
1N3048B
1N3049B
1N3050B
1N3051B
700
25
7
700
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
11
23
8
700
12
21
9
700
13
19
10
700
15
17
14
700
11.4
12.2
13.7
15.2
16.7
18.2
20.6
22.8
25.1
27.4
29.7
32.7
35.8
38.8
42.6
47.1
51.7
56.0
62.2
69.2
76.0
83.6
91.2
98.8
114.0
121.6
136.8
152.0
16
18
15.5
14
16
20
700
750
20
22
24
27
30
33
36
39
43
47
51
56
62
68
75
82
12.5
11.5
10.5
9.5
8.5
7.5
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.7
3.3
3.0
2.8
2.5
2.3
2.0
1.9
1.7
1.6
1.4
1.2
22
23
25
35
40
45
50
60
750
750
750
750
1000
1000
1000
1000
1500
1500
1500
2000
2000
2000
2000
3000
3000
3000
4000
4500
5000
6000
6500
7000
8000
70
80
95
110
125
150
175
200
250
350
450
550
700
1000
1100
1200
1500
12
11
10
91
100
110
120
130
150
160
180
200
9.0
8.3
8.0
6.9
5.7
5.4
4.9
4.6
*JEDEC Registered Data. †Not JEDEC Data.
NOTES: 1. When using JEDEC numbers, B suffix signifies +/-5% tolerance on nominal zener voltage. The suffix A is used to identify +/-10%
tolerance; no suffix indicates +/-20% tolerance: suffix C is used to identify +/- 2%; and suffix D is used to identify +/- 1% tolerance.
2. Zener Voltage (VZ) is measured with junction in thermal equilibrium with still air at a temperature of 25oC. The test currents (IZT) at
nominal voltages provide a constant 0.25 watts.
3. The zener impedance is derived when a 60 cycle ac current having an rms value equal to 10% of the dc zener current (IZT or
I
ZK) is superimposed on IZT or IZK. Zener impedance is measured at 2 points to ensure a sharp knee on the breakdown curve
and to eliminate unstable units. See MicroNote 202 for variation in dynamic impedance with different zener currents.
4. These values of IZM may often be exceeded in the case of individual diodes. The values shown are calculated for a unit at the high
voltage end of its tolerance range. Allowance has also been made for the rise in zener voltage above VZT that results from zener
impedance and the increase in junction temperature as a unit approaches thermal equilibrium at a dissipation of 1 watt. The IZM
values shown for +/-5% tolerance units may be used with little error for +/-10% tolerance units, but should be reduced by 7% to
include a +/-20% tolerance unit near the high voltage end of its tolerance range.
Copyright © 2006
3-12-2006 REV B
Microsemi
Scottsdale Division
Page 2
8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503