Instruction Sheet
408-10376
Extraction Tool 2063388-1
23 Mar 11 Rev B
PROPER USE GUIDELINES
Cumulative Trauma Disorders can resultfrom the prolonged use ofmanually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended-use, production operations is available.
Handle
Sheet 408--9501. The pin and socket contacts are
listed by part number in Figure 1. Read these
instructions thoroughly before attempting to remove
any contacts from the housings.
Dimensions on this sheet are in millimeters [with
inch equivalent dimensions in brackets]. Figures
and illustrations are for identification only and are
not drawn to scale.
NOTE
Tip
i
Plunger
2. DESCRIPTION
PART NUMBERS
FOR MINIATURE RECTANGULAR (MR) CONTACTS
PIN SOCKET
The tool consists of a metal tip and a plastic handle. The
tip is inserted into the mating face of the housing,
depressing the locking lances of the crimped contact.
This action allows the contact to be extracted from the
wire--entry face of the housing.
STRIP
350018
350171
350183
350663
350684
350694
350968
350967
LP
STRIP
350019
350184
350665
350696
-- -- --
LP
350036
350197
350185
350664
350685
350695
640579
640545
350037
350186
350666
350697
-- -- --
3. EXTRACTION PROCEDURE
The procedures which follow are recommended to
extract a crimped contact from a housing. See Figures
2 and 3.
-- -- --
-- -- --
Proceed as follows:
641294
-- -- --
641300
-- -- --
1. Grasp wire of contact to be removed. Push
contact toward mating face of connector and hold
in this position. This will disengage contact locking
lance from shoulder of cavity.
FOR MINIATURE UNIVERSAL MATE-N-LOK* CONTACTS
PIN SOCKET
STRIP
170359
170360
171636
LP
STRIP
170361
170362
171637
LP
2. While holding wire, place tool releasing barrel
over end of contact and push straight into cavity
until it bottoms. The locking lance is now released.
170363
170364
171638
170365
170366
171639
3. Keep releasing barrel firmly bottomed in cavity
and depress plunger (handle). Contact will partially
eject.
FOR COMMERCIAL PIN .062 CONTACTS
STRIP
350629
640391
LP
-- -- --
-- -- --
If difficulty is encountered in pushing contact
forward, Insertion Tool 91002 -1 (tweezer type),
may be used to perform the task from the wire
side of the housing.
NOTE
Figure 1
i
1. INTRODUCTION
4. Pull contact from BACK of connector and
remove tool from cavity.
Extraction Tool 2063388--1, Figure 1, is designed to
remove Miniature Rectangular (MR) contacts,
Miniature Universal MATE--N--LOK contacts, or
Commercial .062 pin contacts from the housings
designed for these contacts. Information for the
removal of Commercial .062 socket contacts with
Extraction Tool 844134--1 can be found on Instruction
Before inserting contact into housing, reset
locking lances to their original positions. Consult
the Customer Drawing covering the specific
contact removed (or consult TE Connectivity
Engineering) for correct setting of locking lances.
NOTE
i
E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
TOOLING ASSISTANCE CENTER 1--800--722--1111 This controlled document is subject to change.
1 of 2
All Rights Reserved
PRODUCT INFORMATION 1--800--522--6752
For latest revision and Regional Customer Service,
visit our website at www.te.com
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.
*Trademark. Other logos, product and/or Company names may be trademarks of their respective owners.
LOC B
5秒后页面跳转
AO3401场效应管参数、引脚图、应用原理图
BT131可控硅参数及引脚图、工作原理详解
74LS32芯片参数、引脚图及功能真值表
全球首块英伟达H200交付 黄仁勋“送货上门”
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
