Datasheet > 1-59619-8

1-59619-8

更新时间： 2024-11-26 01:06:15

品牌	Logo	应用领域
泰科 - TE		/
页数	文件大小	规格书
7页	510K
描述
Application and Maintenance for Crimping Die Assemblies for Tape-Mounted PIDG and PLASTI-GRIP Terminals and Splices

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

1-59619-8 数据手册

Instruction Sheet

Application and Maintenance for Crimping

Die Assemblies for Tape-Mounted PIDG*

and PLASTI-GRIP* Terminals and Splices

408-2423

08 APR 14 Rev B

Die Holding

Screw

Moving Die

Wire Barrel

Crimper

Saddle Screw

Saddle

Insulation

Anvil

Color Code

Dot

Color Code

Dot

Insulation

Crimper

Wire Barrel

Anvil

Die Holding

Screw

Stationary Die

Figure 1

1. INTRODUCTION

The crimping dies listed on this instruction sheet are recommended for crimping the PIDG and PLASTI-GRIP

tape-mounted terminals and splices indicated in Figure 2. The PIDG terminals and splices are used on

stranded copper wire, and the PLASTI-GRIP terminals and splices are used with solid or stranded copper wire.

The dies are designed to be used in AMP-TAPETRONIC* Machine 69875. Refer to Customer Manual

409-1993, packaged with the machine, for information concerning die installation, crimp adjustments, crimping

procedures, and general operation of the machine.

This instruction sheet covers die selection, crimping instructions, and die maintenance and inspection

procedures. Read these instructions thoroughly before crimping any terminals or splices.

NOTE

Measurements are in millimeters [followed by inch equivalents in brackets]. Figures and illustrations are for identification only

and are not drawn to scale.

Reasons for reissue are provided in Section 7, REVISION SUMMARY.

2. DESCRIPTION (Figure 1)

Each die assembly features two stationary dies (anvils) and two moving dies (crimpers), a saddle, and

attaching hardware. One pair of dies (one anvil and one crimper) forms a crimping chamber for the terminal or

splice wire barrel, and the other pair of dies crimps the insulation barrel.

Each half of the die assembly is secured in the machine by a captive screw. The dies are color coded

according to wire size for easy identification. When the terminal or splice is properly crimped in the correct dies,

one or two dots (depending on wire size) will appear on the top and bottom of the terminal or splice.

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

*Trademark

TOOLING ASSISTANCE CENTER 1-800-722-1111

PRODUCT INFORMATION 1-800-522-6752

1 of 7

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

12 3 4 5 6 7

中文翻译

下载PDF

与1-59619-8相关器件

型号	品牌	获取价格	描述	数据表
1596-2	ETC	获取价格	SWAGE/FORCE FIT STANDOFFS
1596279	PHOENIX	获取价格	CONN INSERT 9POS SKT
1596303	PHOENIX	获取价格	Connector Accessory
1596325	PHOENIX	获取价格	Circular Connector,
1596332	PHOENIX	获取价格	Circular Connector,
1596351	PHOENIX	获取价格	Circular Connector,
1596352	PHOENIX	获取价格	Circular Connector,
1596354	PHOENIX	获取价格	Circular Connector,
1596356	PHOENIX	获取价格	Circular Connector,
1596394	PHOENIX	获取价格	Circular Connector,