Document 163-1
™
Micro Spring Air Core Inductors
• Small air core inductors feature high Q and tight tolerances
• Acrylic jacket provides a flat top for pick and place
• Solder coated leads ensure reliable soldering
Terminations RoHS compliant tin-silver over copper Other termina-
tions available at additional cost.
Weight 0906: 10–12mg; 1606: 18 – 27mg
Ambient temperature –40°C to +125°C with Irms current
Maximum part temperature +140°C (ambient + temp rise)
Storage temperature Component: –40°C to +140°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL) +5 to +70 ppm/°C
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging 0906: 500 per 7″ reel Plastic tape: 8 mm wide,
0.3 mm thick, 4 mm pocket spacing, 1.5 mm pocket depth
1606: 500 per 7″ reel Plastic tape: 12 mm wide, 0.3 mm thick,
4 mm pocket spacing, 1.6 mm pocket depth
Recommended pick and place nozzle: OD: 0.059″; ID: 0.035″
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Part
Inductance2
(nH)
Percent
Q4
min
SRFmin5
(GHz)
DCRmax6
(mOhm)
Irms7
(A)
number1
Turns
tolerance3
0906-2_L_
0906-3_L_
0906-4_L_
0906-5_L_
1606-6_L_
2
3
4
5
6
1.65
2.55
3.85
5.40
5.60
10,5
100
100
100
100
100
10.0
8.2
7.5
7.0
6.5
4.0
5.0
6.0
8.0
9.0
1.6
1.6
1.6
1.6
1.6
5,2,1
5,2,1
5,2,1
5,2,1
1606-7_L_
1606-8_L_
1606-9_L_
1606-10_L_
7
8
9
7.15
8.80
9.85
5,2,1
5,2,1
5,2,1
5,2,1
100
100
100
100
6.0
6.0
5.2
4.6
10
12
13
14
1.6
1.6
1.6
1.6
10
12.55
1. When ordering, specify tolerance, termination and packaging codes:
1606-10GLC
2. Inductance measured at 800 MHz using Agilent/HP 4286 or equivalent
with a Coilcraft SMD-A fixture and correlation.
3. Tolerances in bold are stocked for immediate shipment.
4. Q measured at 800 MHz using an Agilent/HP 4291A with an Agilent/
HP 16193A test fixture or equivalents.
Tolerance: F = 1% G = 2% J = 5% K = 10% (Table shows stock
tolerances in bold.)
5. SRF measured using an Agilent/HP 8720D or equivalent with a Coilcraft
SMD-D fixture.
6. DCR tested on the Cambridge Technology Model 510 Micro-ohmmeter
or equivalent.
7. Current that causes a 15°C temperature rise from 25°C ambient.This
information is for reference only and does not represent absolute maxi-
mum ratings.
Termination: L = RoHS compliant tin-silver (96.5/3.5) over copper.
Special order: T = RoHS tin-silver-copper
(95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape, 500 parts per full reel.
B = Less than full reel. In tape, but not machine-ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 163-1 Revised 10/13/15