VS-P400 Series
Vishay Semiconductors
www.vishay.com
ON-STATE CONDUCTION
PARAMETER
SYMBOL
TEST CONDITIONS
Full bridge circuits
VALUES
40
UNITS
A
Maximum DC output current
at case temperature
IO
80
°C
t = 10 ms
t = 8.3 ms
t = 10 ms
t = 8.3 ms
t = 10 ms
t = 8.3 ms
t = 10 ms
t = 8.3 ms
385
400
325
340
745
680
530
480
No voltage
reapplied
Maximum peak, one-cycle
non-repetitive on-state or
forward current
ITSM
IFSM
,
A
100 % VRRM
reapplied
Sinusoidal half wave,
initial TJ = TJ maximum
No voltage
reapplied
Maximum I2t for fusing
I2t
A2s
100 % VRRM
reapplied
t = 0.1 ms to 10 ms, no voltage reapplied
I2t for time tx = I2t · tx
Maximum I2t for fusing
I2t
7450
A2s
Low level value of threshold voltage
High level value of threshold voltage
Low level value of on-state slope resistance
High level value of on-state slope resistance
Maximum on-state voltage drop
VT(TO)1
VT(TO)2
rt1
(16.7 % x x IT(AV) < I < x IT(AV)), TJ = TJ maximum
(I > x IT(AV)), TJ = TJ maximum
0.83
1.03
9.61
7.01
1.4
V
(16.7 % x x IT(AV) < I < x IT(AV)), TJ = TJ maximum
(I > x IT(AV)), TJ = TJ maximum
m
rt2
VTM
VFM
ITM = x IT(AV)
TJ = 25 °C
TJ = 25 °C
V
V
Maximum forward voltage drop
IFM = x IF(AV)
1.4
Maximum non-repetitive rate of rise of
TJ = 125 °C from 0.67 VDRM
dI/dt
200
A/μs
mA
turned-on current
ITM = x IT(AV), Ig = 500 mA, tr < 0.5 μs, tp > 6 μs
Maximum holding current
Maximum latching current
IH
IL
130
250
TJ = 25 °C anode supply = 6 V, resistive load
BLOCKING
PARAMETER
SYMBOL
TEST CONDITIONS
VALUES
UNITS
Maximum critical rate of rise of
off-state voltage
dV/dt
TJ = 125 °C, exponential to 0.67 VDRM gate open
200
V/μs
Maximum peak reverse and off-state
leakage current at VRRM, VDRM
IRRM
IDRM
,
TJ = 125 °C, gate open circuit
TJ = 25 °C
10
mA
μA
V
Maximum peak reverse leakage current
IRRM
100
50 Hz, circuit to base, all terminals shorted,
TJ = 25 °C, t = 1 s
RMS isolation voltage
VISOL
2500
TRIGGERING
PARAMETER
SYMBOL
PGM
TEST CONDITIONS
VALUES
UNITS
Maximum peak gate power
Maximum average gate power
Maximum peak gate current
Maximum peak negative gate voltage
8
2
W
PG(AV)
IGM
2
A
V
-VGM
10
3
TJ = - 40 °C
TJ = 25 °C
Maximum gate voltage required to trigger
Maximum gate current required to trigger
VGT
2
V
TJ = 125 °C
TJ = - 40 °C
TJ = 25 °C
TJ = 125 °C
1
Anode supply =
6 V resistive load
90
60
35
0.2
2
IGT
mA
Maximum gate voltage that will not trigger
Maximum gate current that will not trigger
VGD
IGD
V
TJ = 125 °C, rated VDRM applied
mA
Revision: 27-Mar-14
Document Number: 93755
2
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000