5秒后页面跳转
UP7706ADC8 PDF预览

UP7706ADC8

更新时间: 2022-06-24 15:43:26
品牌 Logo 应用领域
其他 - ETC /
页数 文件大小 规格书
12页 369K
描述
3A Ultra Low Dropout Linear Regulator

UP7706ADC8 数据手册

 浏览型号UP7706ADC8的Datasheet PDF文件第1页浏览型号UP7706ADC8的Datasheet PDF文件第3页浏览型号UP7706ADC8的Datasheet PDF文件第4页浏览型号UP7706ADC8的Datasheet PDF文件第5页浏览型号UP7706ADC8的Datasheet PDF文件第6页浏览型号UP7706ADC8的Datasheet PDF文件第7页 
uP7706  
Functional Pin Description  
Pin No. Name Pin Function  
Power OK Indication. This pin is an open-drain output and is set high impedance once VOUT  
1
2
POK  
EN  
reaches 92% of its rating voltage.  
Enable Input. Pulling this pin below 0.8V turns the regulator off, reducing the quiescent current  
to a fraction of its operating value.  
Input Voltage. This is the drain input to the power device that supply current to the output pin.  
Large bulk capacitors with low ESR should be placed physically close to this pin o prevent the  
input rail from dropping during large load transient. A 10uF ceramic capacitor is recommended  
at this pin.  
3
VIN  
Supply Input for Control Circuit. This pin provides bias voltage to the control circuitry and  
driver for the pass transistor.The driving capability of output current is proportioned to the VCNTL  
.
4
5
6
CNTL  
NC  
For the device to regulate, the voltage on this pin must be at least 1.5V greater than the output  
voltage, and no less than VCNTL_MIN.  
Not Internally Connected.  
Output Voltage. This pin is power output of the device. A pull low resistance exists when the  
device is disabled by pulling low the EN pin. To maintain adequate transient response to large  
load change, typical value of 1000uF Al electrolytic capacitor with 10uF ceramic capacitors are  
recommended to reduce the effects of current transients on VOUT.  
VOUT  
Feedback Voltage. This pin is the inverting input to the error amplifier. A resistor divider from  
7
8
FB  
the output to GND is used to set the regulation voltage as VOUT = 0.8x(R1+R2)/R1 (V)  
Ground.  
GND  
GND  
Exposed  
Pad  
Ground. The exposed pad acts the dominant power dissipation path and should be soldered  
to well design PCB pads as described in the Application Informations Chapter.  
Functional Block Diagram  
EN  
2
CNTL  
4
VIN  
3
Power On  
Reset  
Thermal Limit  
0.3V  
Softstart &  
Control Logic  
Current Limit  
7
FB  
0.8V VREF  
6
Delay  
92% VREF  
8
1
POK  
GND  
uPI Semiconductor Corp., http://www.upi-semi.com  
Rev. F00, File Name: uP7706-DS-F0000  
2

与UP7706ADC8相关器件

型号 品牌 描述 获取价格 数据表
UP7706U8 ETC 3A Ultra Low Dropout Linear Regulator

获取价格

UP7718 UNITPOWER 3A Ultra Low Dropout Linear Regulator

获取价格

UP7718A UNITPOWER 3A Ultra Low Dropout Linear Regulator

获取价格

UP8001A UPI Li-ion/Li Polymer Battery Charger

获取价格

UP8001ADAA-41 UPI Li-ion/Li Polymer Battery Charger

获取价格

UP8001ADAA-42 UPI Li-ion/Li Polymer Battery Charger

获取价格