uP7706
Electrical Characteristics
Parameter
Symbol
Test Conditions
Min
Typ
Max
Units
Feedback Voltage
Reference Voltage
Feedback Input Current
VREF
IFB
VCNTL = VIN = VEN = 5.0V, IOUT = 0A. VOUT = VREF
0.788 0.8
0.812
--
V
--
20
nA
1.2V < VIN < 5.0V, VCNTL = VEN = 5.0V, IOUT = 0A. VOUT
VREF
=
VIN Line Regulation
VREF(LINE)
--
0.01
0.1
%/V
VCNTL Line Regulation
Load Regulation
VREF(CNTL) VIN = 3.3V, IOUT = 0A. VOUT = VREF
--
--
0.01
0.8
0.1
1.5
%/V
%/A
VREF(LOAD) 10mA < IOUT < 3A, VCNTL = VIN = VEN = 5.0V, VOUT = VREF
Load Regulation over
Temperature
10mA < IOUT < 3A, VCNTL = VIN = VEN = 5.0V, VOUT = VREF,
VREF(LOAD)
--
--
1.4
3
%
-40OC < TJ < 125OC
IOUT = 2A, VCNTL = VEN = 5.0V, VOUT = VREF
VDROP
200
300
240
360
Dropout Voltage
mV
I OUT = 3A, VCNTL = VEN = 5.0V, VOUT = VREF
VOUT Pull Low Resistance
VCNTL = VIN = 5.0V, VEN = 0V,
--
90
--
Ω
Enable
Enable High Level
Disable Low Level
EN Input Current
EN Input Impedance
PWROK
VEN
VSD
--
0.8
--
--
--
1.4
--
V
V
IEN
VEN = VCNTL = 5.0V
12
65
20
--
uA
KΩ
ZEN
--
FB Power OK Threshold VPOKTH
IOUT = 0A, VCNTL = VIN = VEN = 5.0V, VOUT = VREF
IOUT = 0A, VCNTL = VIN = VEN = 5.0V, VOUT = VREF
--
--
92
8
--
--
%
%
Power OK Hysteresis
Overcurrent Protection
OCP Threshold Level
VPOKHYS
IOCP
ISC
VCNTL = VIN = VEN = 5.0V, VOUT = VREF
VCNTL = VIN = VEN = 5.0V, VOUT = VREF
--
--
4
--
--
A
Output Short Circuit
Current
100
mA
Thermal Protection
Thermal Shutdown
Temperature
TSD
IOUT = 0A, VCNTL = VIN = VEN = 5.0V, VOUT = VREF
IOUT = 0A, VCNTL = VIN = VEN = 5.0V, VOUT = VREF
--
--
170
30
--
--
OC
OC
Thermal Shutdown
Hysteresis
TSDHYS
Note 1. Stresses listed as the above “Absolute Maximum Ratings” may cause permanent damage to the device.
These are for stress ratings. Functional operation of the device at these or any other conditions beyond those
indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may remain possibility to affect device reliability.
Note 2. Devices are ESDsensitive. Handling precaution recommended.
Note 3. θJA is measured in the natural convection at TA = 25°C on a low effective thermal conductivity test board of
JEDEC 51-3 thermal measurement standard.
Note 4. The device is not guaranteed to function outside its operating conditions.
uPI Semiconductor Corp., http://www.upi-semi.com
Rev. F00, File Name: uP7706-DS-F0000
5