TRUMPower
The TUP110 series of AC/DC switching power
supplies are for 110 watts of continuous output
110 WATT POWER ADAPTERS
DESCRIPTION
TUP110 SERIES
(LVD+EMC)
power. They are enclosed in
a
94V-1 rated
polyphenylene-oxide case with an IEC 320 inlet to
mate with interchangeable cord for world-wide
use. An on/off switch can be added at request. All
models meet CISPR 22 and FCC class B emission
limits, and comply with UL, CSA, IEC and CE
requirements.
FEATURES
‧ Single, dual, triple or quadruple outputs
‧ Optional output connectors
‧ Optional on/off switch
Safety Standard Approvals：
UL 60950-1
CSA C22.2 No. 60950-1
‧ Optional Power Fail Detect (PFD) signal
‧ 100% burn-in
‧ Wide input range 85 to 264 VAC
‧ Input surge current protection
‧ Overvoltage protections
TÜV EN60950-1
‧ Overcurrent protections
ENVIRONMENTAL SPECIFICATIONS
INPUT SPECIFICATIONS
Operating temperature：
Storage temperature：
Relative humidity：
Derating：
0ºC to +70ºC
Input voltage：
Input frequency： 47 to 63 Hz
Input current： 3.20A（ rms） for 115VAC
1.80A（ rms） for 230VAC
85 to 264 VAC
-40ºC to +85ºC
5% to 95% non-condensing
Derate from 100% at +50ºC
linearly to 50% at +70ºC
Leakage current： 0.40mA max. @ 115VAC, 60Hz
0.80mA max. @ 230VAC, 50Hz
OUTPUT SPECIFICATIONS
Output voltage/current： See rating chart
GENERAL SPECIFICATIONS
Switching frequency： 20K to 250KHz, varies with load and
Total output power：
Ripple and noise：
Overvoltage protection： Provided on output #1 only; set
at 112 – 132% of its nominal
110 watts maximum
1% peak to peak maximum
line
Efficiency：
70% minimum on single output
models with Vo ≥12V, 65% minimum
on the others
output voltage
Hold-up time：
Line regulation：
Inrush current：
12 msec minimum at 110VAC
±0.5% maximum at full load
15 amps @ 115VAC, or 30 amps
@ 230VAC, at 25ºC cold start
3000VAC from input to output
1500VAC from input to ground
500VAC from output to ground
550,000 hours minimum at full load
at 25ºC ambient , calculated per
MIL-HDBK-217F, excluding DC fan
Overcurrent protection： All outputs protected to short
circuit conditions
Temperature coefficient： All outputs ±0.04%/ºC
maximum
Withstand voltage：
MTBF：
Transient response：
Maximum excursion of 4% or
better on all models, recovering
to 1% of final value within
500µs after a 25% step load
change
TTL logic high for normal
operation and TTL logic low
upon loss of input power. This
signal appears at least 1ms
prior to +5V output dropping
5% below its nominal value.
This signal also provides a
minimum delay of 100ms after
+5V is within regulation.
EMC performance (EN55024)
EN55022:
FCC:
VCCI:
EN61000-3-2:
EN61000-3-3:
EN61000-4-2:
EN61000-4-3:
EN61000-4-4:
EN61000-4-5:
EN61000-4-6:
EN61000-4-8:
PFD signal (optional)：
Class B conducted, class B radiated
Class B conducted, class B radiated
Class B conducted, class B radiated
Harmonic distortion, class A
Line flicker
ESD, ±8KV air and ±4KV contact
Radiated immunity, 3V/m
Fast transient/burst, ±1KV
Surge, ±1KV diff, ±2KV com.
Conducted immunity, 3Vrms
Magnetic field immunity, 1A/m
EN61000-4-11: Voltage dips, 30% reduction for 500ms and
>95% reduction for 10ms
Tumbler Technologies + TRUMPower
3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA
Phone: 408-988-6616 ● Fax: 408-988-6622 ● email: sales@trumpower.com ● Website: www.TRUMPower.com
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
