TPS629210-Q1
SLVSFS6B – MAY 2021 – REVISED DECEMBER 2021
TPS629210-Q1 3-V to 17-V, 1-A Low IQ Buck Converter in a SOT-583 Package
1 Features
3 Description
•
AEC-Q100 qualified for automotive applications:
– –40°C to 150°C operating junction temperature
range
– Level 2 device HBM ESD classification
– Level C4B CDM ESD classification
Functional Safety-Capable
– Documentation available to aid functional safety
system design
High-efficiency DCS-Control™ topology
4-µA typical low quiescent current
Dynamically selectable forced PWM or auto power
save mode operations
2.5-MHz or 1.0-MHz selectable switching
frequencies
Output current up to 1 A
RDSON: 250-mΩ high side, 85-mΩ low side
Output voltage accuracy of ± 1%
Configurable output voltage options:
– VFB external divider: 0.6 V to 5.5 V
– VSET internal divider:
The automotive-qualified TPS6292xx-Q1 family of
devices are highly efficient, small, and highly flexible
synchronous step-down DC-DC converters that are
easy to use. A wide 3-V to 17-V input voltage range
supports a wide variety of systems powered from
either 12-V, 5-V, or 3.3-V supply rails, or single-cell
or multi-cell Li-Ion batteries. The TPS629210-Q1 can
be configured to run at either 2.5 MHz or 1 MHz
in a forced PWM mode or a variable frequency
(auto PFM) mode. In auto PFM mode, the device
automatically transitions to power save mode at
light loads to maintain high efficiency. The low 4-µA
typical quiescent current also provides high efficiency
down to the smallest loads. TI's automatic efficiency
enhancement (AEE) mode holds a high conversion
efficiency through the whole operation range without
the need of using different inductors by automatically
adjusting the switching frequency based on input and
output voltages. In addition to selecting the switching
frequency behavior, the MODE/S-CONF input pin can
also be used to select between different combinations
of external and internal feedback dividers and
enabling and disabling the output voltage discharge
capability. In the internal feedback configuration, a
resistor between the FB/VSET pin and GND can be
used to select between 18 different output voltage
options (see Table 8-2).
•
•
•
•
•
•
•
•
•
•
18 options between 0.4 V and 5.5 V
•
•
•
•
•
•
•
No external bootstrap capacitor required
Output overcurrent and overtemperature protection
100% duty cycle mode
Precise enable input
Power-good output
Selectable active output discharge
Pin-to-pin compatible with the TPS629206-Q1 and
TPS629203-Q1 devices
Device Information
PART NUMBER
PACKAGE(1)
BODY SIZE (NOM)
•
0.5-mm pitch, 8-pin SOT-583 package
1.60 mm × 2.10 mm
(including pins)
TPS629210-Q1
SOT-583 (8)
2 Applications
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
•
•
•
VIN
ADAS and infotainment
Telecom and wireless infrastructure
Factory automation and control
100
90
80
70
60
50
40
VOUT
0.4V œ 5.5V
2.2 µH
3V œ 17V
VIN
EN
SW
22 ꢀF
4.7 ꢀF
VOS
FB/
VSET
MODE/
S-CONF
30
PG
VIN = 6V
VIN = 9V
20
GND
VIN = 12V
VIN = 15V
10
0
1E-5
0.0001
0.001
Iout (A)
0.01
0.1 0.2 0.5 1
Simplified Schematic
Efficiency Versus Output Current
VOUT = 3.3 V at 2.5 MHz Auto PFM/PWM
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.