5秒后页面跳转
TLE4941 PDF预览

TLE4941

更新时间: 2024-01-24 08:32:11
品牌 Logo 应用领域
英飞凌 - INFINEON 传感器换能器磁场传感器信息通信管理
页数 文件大小 规格书
11页 786K
描述
Differential Two-Wire Hall Effect Sensor IC

TLE4941 技术参数

是否Rohs认证: 符合生命周期:Contact Manufacturer
包装说明:SSO-2Reach Compliance Code:compliant
Factory Lead Time:26 weeks风险等级:5.76
主体宽度:1 mm主体高度:3.71 mm
主体长度或直径:5.34 mm外壳:PLASTIC
最大磁场范围:20 mT最小磁场范围:-20 mT
安装特点:THROUGH HOLE MOUNT最大工作电流:8.4 mA
最大输出电流:26 mA输出接口类型:2-WIRE INTERFACE
输出类型:DIGITAL CURRENT封装形状/形式:RECTANGULAR
传感器/换能器类型:MAGNETIC FIELD SENSOR,HALL EFFECT表面贴装:NO
端接类型:SOLDERBase Number Matches:1

TLE4941 数据手册

 浏览型号TLE4941的Datasheet PDF文件第1页浏览型号TLE4941的Datasheet PDF文件第3页浏览型号TLE4941的Datasheet PDF文件第4页浏览型号TLE4941的Datasheet PDF文件第5页浏览型号TLE4941的Datasheet PDF文件第6页浏览型号TLE4941的Datasheet PDF文件第7页 
TLE4941, TLE4941C  
Functional Description  
The differential hall sensor IC detects the motion of ferromagnetic and permanent  
magnet structures by measuring the differential flux density of the magnetic field. To  
detect the motion of ferromagnetic objects the magnetic field must be provided by a  
back biasing permanent magnet. Either south or north pole of the magnet can be  
attached to the rear unmarked side of the IC package.  
Magnetic offsets of up to +/- 20mT and device offsets are cancelled by a self-  
calibration algorithm. Only a few transitions are necessary for self-calibration. After  
the initial calibration sequence switching occurs when the input signal is crossing the  
arithmetic mean of its max and min value. (E.g. zero-crossing for sinusoidal signals)  
The ON and OFF state of the IC are indicated by High and Low current  
consumption.  
Circuit Description  
The circuit is supplied internally by a 3V voltage regulator. An on-chip oscillator  
serves as clock generator for the digital part of the circuit.  
TLE4941 signal path is comprised of a pair of hall probes, spaced at 2.5mm, a  
differential amplifier including a noise-limiting low-pass filter and a comparator  
feeding a switched current output stage. In addition an offset cancellation feedback  
loop is provided by a signal-tracking A/D converter, a digital signal processor (DSP)  
and an offset cancellation D/A converter.  
During the startup phase (un-calibrated mode) the output is disabled (I=ILow).  
The differential input signal is digitized in the speed A/D converter and fed into the  
DSP. The minimum and maximum values of the input signal are extracted and their  
corresponding arithmetic mean value is calculated. The offset of this mean value is  
determined and fed into the offset cancellation DAC.  
After successful correction of the offset, the output switching is enabled.  
In running mode (calibrated mode) the offset correction algorithm of the DSP is  
switched into a low-jitter mode, avoiding oscillation of the offset DAC LSB. Switching  
occurs at zero-crossing. It is only affected by the (small) remaining offset of the  
comparator and by the remaining propagation delay time of the signal path, mainly  
determined by the noise-limiting filter. Signals below a defined threshold DBLimit are  
not detected to avoid unwanted parasitic switching.  
TLE4941 - TLE 4941C Data Sheet  
2
Febrary 2002  

与TLE4941相关器件

型号 品牌 获取价格 描述 数据表
TLE4941-1C INFINEON

获取价格

Analog Circuit, 1 Func, PSSS2, PLASTIC, SSO-2
TLE4941-1C-HT INFINEON

获取价格

Analog Circuit,
TLE4941-2 INFINEON

获取价格

Differential Two-Wire Hall Effect Sensor IC
TLE4941-2C INFINEON

获取价格

Differential Two-Wire Hall Effect Sensor IC
TLE4941C INFINEON

获取价格

Differential Two-Wire Hall Effect Sensor IC
TLE4941CBAMA1 INFINEON

获取价格

Hall Effect Sensor, 0-20mT Min, 20mT Max, BICMOS, Plastic/Epoxy, Rectangular, Through Hole
TLE4941CE6735BTMA1 INFINEON

获取价格

Hall Effect Sensor,
TLE4941CHAMA2 INFINEON

获取价格

Hall Effect Sensor,
TLE4941PLUSC INFINEON

获取价格

Analog Circuit, 1 Func, BICMOS, PXSS2, SSO-2-53, 2 PIN
TLE4941PLUSCAAMA1 INFINEON

获取价格

Analog Circuit,