TK112xxB
ABSOLUTE MAXIMUM RATINGS TK112xxBC (VOUT ≥ 2.0 V)
Supply Voltage ......................................................... 16 V
Power Dissipation SOT-23L (Note1) .................. 600 mW
Power Dissipation SOT-89 (Note1) .................... 900 mW
Reverse Bias............................................................ 10 V
Storage Temperature Range ................... -55 to +150 °C
Operating Temperature Range ...................-30 to +80 °C
Operating Voltage Range............................ 1.8 to 14.5 V
Junction Temperature ........................................... 150 °C
TK112xxBC ELECTRICAL CHARACTERISTICS (VOUT ≥ 2.0 V)
Test conditions: T = 25 °C, unless otherwise specified.
A
SYMBOL
IQ
ISTBY
VOUT
PARAMETER
Quiescent Current
Standby Current
Output Voltage
TEST CONDITIONS
IOUT = 0 mA, Excluding ICONT
VIN = 8 V, Output OFF
IOUT = 30 mA
MIN
TYP
MAX
250
0.1
UNITS
µA
170
µA
See Table 1
V
VOUT ≤ 5.5 V, (Note 2)
VOUT ≥ 5.6 V, (Note 2)
3.0
15
20
40
mV
mV
mV
mV
mV
V
Line Reg Line Regulation
I
I
I
OUT = 1 to 60 mA, (Note 2)
OUT = 1 to 100 mA, (Note 2)
OUT = 1 to 150 mA, (Note 2)
6
30
Load Reg Load Regulation
18
60
23
90
IOUT = 60 mA, (Note 2)
OUT = 150 mA, (Note 2)
Continuous Output Current (Note 2)
0.12
0.26
0.20
0.39
150
180
VDROP
Dropout Voltage
I
V
IOUT
mA
mA
IOUT(PULSE)
Pulse Output Current
5 ms pulse, 12.5 % duty cycle
f = 400 Hz, CL = 10 µF, CN = 0.1 µF,
VIN = VOUT + 1.5 V, IOUT = 30 mA,
VRIPPLE = 100 mVrms, (Note 3)
RR
VNO
Ripple Rejection
60
30
dB
10 Hz ≤ f ≤ 80 kHz, CL = 10 µF,
CN = 0.1 µF, VCN = VOUT + 1.5 V,
IOUT = 60 mA, (Notes 3,4)
Output Noise Voltage
µVrms
Noise Bypass Terminal
Voltage
Vref
1.25
40
V
∆VOUT /∆T
Temperature Coefficient
I
OUT = 10 mA
ppm/° C
CONTROL TERMINAL SPECIFICATIONS
ICONT
Control Current
VCONT = 1.8 V, Output ON
Output ON
12
35
µA
V
VCONT(ON)
Control Voltage ON
1.8
VCONT(OFF) Control Voltage OFF
Output OFF
0.6
V
Note 1: When mounted as recommended. Derate at 4.8 mW/°C for SOT-23L and 6.4 mW/°C for SOT-89 packages for operation above 25°C.
Note 2: Refer to “Definition of Terms.”
Note 3: Ripple rejection and noise voltage are affected by the value and characteristics of the capacitor used.
Note 4: Output noise voltage can be reduced by connecting a capacitor to a noise pass terminal.
Gen. Note: Parameters with min. or max. values are 100% tested at TA = 25 °C.
Page 2
October 1999 TOKO, Inc.