Datasheet > TDA9897HN

TDA9897HN

更新时间： 2022-04-23 23:00:11

品牌	Logo	应用领域
恩智浦 - NXP		/
页数	文件大小	规格书
103页	512K
描述
Multistandard hybrid IF processing

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

TDA9897HN 数据手册

TDA9897; TDA9898

NXP Semiconductors

Multistandard hybrid IF processing

16. Soldering

16.1 Introduction

There is no soldering method that is ideal for all surface mount IC packages. Wave

soldering can still be used for certain surface mount ICs, but it is not suitable for ﬁne pitch

SMDs. In these situations reﬂow soldering is recommended.

16.2 Through-hole mount packages

16.2.1 Soldering by dipping or by solder wave

Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 °C

or 265 °C, depending on solder material applied, SnPb or Pb-free respectively.

The total contact time of successive solder waves must not exceed 5 seconds.

The device may be mounted up to the seating plane, but the temperature of the plastic

body must not exceed the speciﬁed maximum storage temperature (T_stg(max)). If the

printed-circuit board has been pre-heated, forced cooling may be necessary immediately

after soldering to keep the temperature within the permissible limit.

16.2.2 Manual soldering

Apply the soldering iron (24 V or less) to the lead(s) of the package, either below the

seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is

less than 300 °C it may remain in contact for up to 10 seconds. If the bit temperature is

between 300 °C and 400 °C, contact may be up to 5 seconds.

16.3 Surface mount packages

16.3.1 Reﬂow soldering

Key characteristics in reﬂow soldering are:

• Lead-free versus SnPb soldering; note that a lead-free reﬂow process usually leads to

higher minimum peak temperatures (see Figure 54) than a PbSn process, thus

reducing the process window

• Solder paste printing issues including smearing, release, and adjusting the process

window for a mix of large and small components on one board

• Reﬂow temperature proﬁle; this proﬁle includes preheat, reﬂow (in which the board is

heated to the peak temperature) and cooling down. It is imperative that the peak

temperature is high enough for the solder to make reliable solder joints (a solder paste

characteristic). In addition, the peak temperature must be low enough that the

packages and/or boards are not damaged. The peak temperature of the package

depends on package thickness and volume and is classiﬁed in accordance with

Table 58 and 59

TDA9897_TDA9898_3

Product data sheet

Rev. 03 — 11 January 2008

97 of 103

1...94 95 969798 99 100...103

下载PDF

与TDA9897HN相关器件

型号	品牌	描述	获取价格	数据表
TDA9897HN/V2	NXP	IC SPECIALTY CONSUMER CIRCUIT, PQCC48, 7 X 7 MM, 0.85 MM HEIGHT, PLASTIC, SOT619-1, MO-220	获取价格
TDA9897HN/V3	NXP	Multistandard hybrid IF processing	获取价格
TDA9897HN/V3,551	NXP	TDA9897; TDA9898 - Multistandard hybrid IF processing QFN 48-Pin	获取价格
TDA9897HN/V3,557	NXP	TDA9897; TDA9898 - Multistandard hybrid IF processing QFN 48-Pin	获取价格
TDA9897S1	NXP	Multistandard hybrid IF processing	获取价格
TDA9897V2	NXP	Multistandard hybrid IF processing	获取价格