SGM4056
High Input Voltage Charger
ELECTRICAL CHARACTERISTICS
(VIN = 5V, RIMIN = 243kΩ, TA = +25℃, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
RECOMMENDED OPERATING CONDITIONS
Maximum Supply Voltage
26.5
6.10
9.35
900
V
V
SGM4056-6.8
Operating
4.55
4.55
100
Supply Voltage
SGM4056-10.5
Programmed Charge Current
mA
POWER-ON RESET
Rising POR Threshold
Falling POR Threshold
VIN-BAT OFFSET VOLTAGE
Rising Edge
VPOR
3.21
2.86
3.95
3.60
4.55
4.35
V
V
V
use
BAT = 3.0V, RIREF = 120kΩ,
to indicate the comparator output.
PPR
VPOR
VOS
VOS
110
60
200
mV
mV
VBAT = 4.5V, RIREF = 120kΩ, use
pin to
PPR
indicate the comparator output. (1)
Falling Edge
5
OVER-VOLTAGE PROTECTION
SGM4056-6.8
6.10
9.35
140
245
6.80
10.50
220
7.26
11.15
300
Over-Voltage
Protection Threshold
VOVP
V
SGM4056-10.5
SGM4056-6.8
SGM4056-10.5
VBAT = 4.3V, RIREF = 120kΩ,
use
to indicate the comparator output.
PPR
OVP Threshold
Hysteresis
VOVPHYS
mV
340
430
STANDBY CURRENT
BAT Pin Sink Current
VIN Pin Supply Current
VIN Pin Supply Current
ISTANDBY
IVIN
Charger disabled or the input is floating
VBAT = 4.3V, RIREF = 24.3kΩ, charger disabled
VBAT = 4.3V, RIREF = 24.3kΩ, charger enabled
1
μA
μA
μA
200
270
275
320
IVIN
VOLTAGE REGULATION
RIREF = 24.3kΩ, 4.55V < VIN < 6.10V,
charge current = 20mA
4.152
4.152
4.2
4.2
0.7
4.248
4.248
Output Voltage
VCH
V
RIREF = 24.3kΩ, 4.55V < VIN < 9.35V,
charge current = 20mA
VBAT = 3.8V, charge current = 500mA,
PMOS On Resistance
RDS (ON)
Ω
RIREF = 10kΩ
CHARGE CURRENT (2)
IREF Pin Output Voltage
Constant Charge Current
Trickle Charge Current
End-of-Charge Current
EOC Rising Threshold
VIREF
IREF
ITRK
IMIN
VBAT = 3.8V, RIREF = 120kΩ
RIREF = 24.3kΩ, VBAT = 2.8V to 3.8V
RIREF = 24.3kΩ, VBAT = 2.4V
RIREF = 24.3kΩ
1.162
440
55
1.215
500
90
1.262
560
135
75
V
mA
mA
mA
mA
20
40
RIREF = 24.3kΩ
315
370
435
PRECONDITIONING CHARGE THRESHOLD
Preconditioning Charge
Threshold Voltage
VMIN
VMINHYS
RIREF = 24.3kΩ
RIREF = 24.3kΩ
2.46
20
2.55
100
2.65
190
V
Preconditioning Voltage Hysteresis
mV
NOTES:
1. The 4.5V VBAT is selected so that the
output can be used as the indication for the offset comparator output indication. If
PPR
the VBAT is lower than the POR threshold, no output pin can be used for indication.
2. The charge current can be affected by the thermal foldback function if the IC under the test setup cannot dissipate the heat.
SG Micro Corp
www.sg-micro.com
OCTOBER 2017
4