PT6460 Series
14-A 5-V Input Adjustable
Integrated Switching Regulator
SLTS178B - JANUARY 2003 - REVISED JUNE 2003
Specifications (Unless otherwise stated, Ta =25 °C, Vin =5 V, Cin =470 µF, Cout =0 µF, and Io =Iomax)
PT6460 SERIES
Characteristics
Symbols
Conditions
Min
Typ
Max
Units
Output Current
Io
Vin
Vin =5 V
Over Io range
0
—
—
—
0.5
10
12
14
5.5
2
—
—
—
A
V
%Vo
%Vo
mV
mV
Input Voltage Range
Set-Point Voltage Tolerance
Temperature Variation
Line Regulation
Load Regulation
Total Output Variation
4.5
—
—
—
—
Vo tol
∆Regtemp
∆Regline
∆Regload
∆Regtot
–40 °C <Ta < +85 °C
Over Vin range
Over Io range
Includes set-point, line, load,
—
—
3
%Vo
–40 °C ≤ Ta ≤ +85 °C
Efficiency
η
Io =10 A
PT6461 (3.3 V)
PT6462 (2.5 V)
PT6463 (2.0 V)
PT6464 (1.8 V)
PT6465 (1.5 V)
PT6466 (1.2 V)
PT6467 (1.0 V)
—
—
—
—
—
—
—
94
93
91
90
88
86
84
—
—
—
—
—
—
—
%
Vo Ripple (pk-pk)
Vr
20MHz
bandwidth—
25
—
mVpp
Transient Response
1 A/µs load step, 50 to 100 % Iomax,
Cout =330 µF
ttr
Recovery Time
Vo over/undershoot
—
—
50
—
—
µSec
mV
∆Vtr
100
Over-Current Threshold
Output Voltage Adjust
Switching Frequency
ITRIP
Vo adj
ƒs
Reset, followed by auto-recovery
—
—
—
27.5
15
300
—
—
—
A
%
kHz
(1)
Over Vin and Io ranges
Inhibit Control (pin1)
Input High Voltage
Input Low Voltage
Referenced to GND (pins 5–8)
(2)
VIH
VIL
IIL
Vin –0.5
–0.2
—
—
—
—
–10
5
—
330
—
—
—
Open
0.8
—
—
—
3,300
85
215
125
V
Input Low Current
Pin 1 to GND
Pin 1 to GND
µA
mA
µF
µF
°C
°C
°C
Inhibit Input Current
External Input Capacitance
External Output Capacitance
Operating Temperature Range
Solder Reflow Temperature
Storage Temperature
Iin inhibit
Cin
Cout
(3)
470
(4) (5)
0
(5)
(6)
T
Over Vin range
Surface temperature of module pins or case
—
–40
a
(7)
Treflow
T
s
—
–40
Reliability
MTBF
Per Bellcore TR-332
50 % stress, Ta =40 °C, ground benign
6
8.0
—
—
10 Hrs
Mechanical Shock
Mil-STD-883D, Method 2002.3
Half Sine, mounted to a fixture
—
500
—
G
(8)
(8)
Mechanical Vibration
Mil-STD-883D, Method 2007.2,
20-2000 Hz, PCB mounted
Suffix N
Suffixes A, C
—
—
20
20
—
—
G
Weight
Flammability
—
—
—
—
10
—
grams
Materials meet UL 94V-0
Notes: (1) This is a typical value. For the adjustment limits of a specific model consult the related application note on output voltage adjustment.
(2) The Inhibit control (pin 1) has an internal pull-up, and if left open-circuit the module will operate when input power is applied. A small low-leakage
(<100 nA) MOSFET is recommended to control this input. See application notes for more information.
(3) A 470 µF electrolytic input capacitor is required for proper operation. The capacitor must be rated for a minimumm of 0.7 Arms of ripple current.
(4) An external output capacitor is not required for basic operation. Adding 330 µF of distributed capacitance at the load will improve the transient response.
(5) For operation below 0 °C, COUT should have stable characteristics. Use either low-ESR tantalum or Oscon® type capacitors.
(6) See SOA curves or consult factory for the appropriate derating.
(7) During solder reflow of SMD package version do not elevate the module case, pins, or internal component temperature above a peak of 215 °C. For
further guidance refer to the application note, “Reflow Soldering Requirements for Plug-in Power Surface Mount Products,” (SLTA051).
(8) The case pins on the through-hole package types (suffixes N & A) must be soldered. For more information see the applicable package outline drawing.
For technical support and more information, see inside back cover or visit www.ti.com