PT4520 Series
20-W 48-V Input Isolated
DC/DC Converter
SLTS148B - JUNE 2000 - REVISED OCTOBER 2002
Specifications (Unless otherwise stated, Ta =25°C, Vin =48V, Cout =0µF, and Io =Iomax)
PT4520 SERIES
Characteristic
Symbol
Conditions
Min
Typ
Max
Units
(1)
Output Current
Io
Over Vin range
Vo = 15V
Vo = 12V
Vo =5.0V
Vo ≤3.3V
0.1
—
—
—
—
1.3
1.6
4
0.1 (1)
A
(1)
0.1
(1)
0.1
5
Input Voltage Range
Set-Point Voltage Tolerance
Temperature Variation
Line Regulation
Load Regulation
Total Output Voltage Variation
Vin
Over Io Range
36
—
—
—
—
48
1
0.5
0.2
0.4
75
1.5
—
1
VDC
%Vo
%Vo
%Vo
%Vo
(2)
Vo tol
Regtemp
Regline
Regload
∆Votot
–40° ≤Ta ≤ +85°C, Io =Iomin
Over Vin range
Over Io range
Includes set-point, line, load,
–40° ≤Ta ≤ +85°C
(2)
(2)
1
—
2
3
%Vo
Efficiency
η
Vo = 15V
Vo = 12V
Vo=5.0V
Vo=3.3V
Vo=1.8V
Vo=1.5V
Vo=1.2V
—
—
—
—
—
—
—
86
83
82
78
67
65
59
—
—
—
—
—
—
—
%
Vo Ripple (pk-pk)
Vr
20MHz bandwidth
Vo ≥5.0V
Vo ≤3.3V
—
—
—
—
—
—
—
0.5
15
100
3
150
200
10
650
850
—
—
—
—
—
—
—
%Vo
mVpp
µs
%Vo
mV
Transient Response
ttr
0.1A/µs load step, 50% to 100% Iomax
Vo over/undershoot
Vo ≥5.0V
Vo ≤3.3V
∆Vtr
Current Limit Threshold
Output Voltage Adjust
Switching Frequency
Ilim
Vo adj
ƒs
Vin =36V, ∆Vo = –50mV
%Iomax
%
Over Vin range
Vo ≥5.0V
Vo ≤3.3V
600
800
—
700
900
—
kHz
V
Under-Voltage Lockout
UVLO
31
Remote On/Off (Pin 1)
High-Level Input Voltage
Low-Level Input Voltage
Low-Level Input Current
Referenced to –Vin (pin 2)
pins 1 & 2 connected
(3)
VIH
VIL
IIL
2.5
—
—
–10
7
0.5
—
Open
0.8
–
10
—
220
V
–0.2
—
—
—
0
µA
mA
µF
µF
Standby Input Current
Internal Input Capacitance
External Output Capacitance
Iin standby
Cin
Cout
(4)
Isolation Voltage
Capacitance
Resistance
Input–output/input–case
Input to output
1500
—
—
1100
—
—
—
—
V
pF
MΩ
Input to output
10
(5)
Operating Temperature Range
Solder Reflow Temperature
Storage Temperature
Reliability
T
Treflow
Over Vin range
Surface temperature of module pins or case
—
–40
—
–40
—
—
—
85
215
125
°C
°C
°C
a
(6)
T
s
MTBF
Per Bellcore TR-332
6
4
—
—
10 Hrs
50% stress, Ta =40°C, ground benign
Mechanical Shock
—
Per Mil-Std-883D, method 2002.3,
1mS, half-sine, mounted to a fixture
—
500
—
G’s
(7)
(7)
Mechanical Vibration
—
Mil-Std-883D, method 2007.2,
20-2000Hz , soldered
Suffix N
Suffixes A & C
—
—
20
—
—
G’s
20
Weight
Flammability
—
—
—
—
23
—
grams
Materials meet UL 94V-0
Notes: (1)The DC/DC converter will operate at no load with reduced specifications.
(2) For optimum voltage accuracy the ‘Remote Sense (+)’ and ‘Remote Sense (–)’ pins must be connected to +Vout and –Vout respectively.
(3)The Remote On/Off (pin 1) has an internal pull-up, and if it is left open circuit the PT4520 will operastaeppwliehde.nReifnerputto thpeower
application notes for interface considerations.
i
(4)External output capacitance is not required for proper operation. Capacitamce may be added to improve threanrsieesnpotsn.sTe hetomaloxaimd umt
total capacitance (including the load circuit) must not exceed 220µF, and the combined ESR of must not be less than 100mΩ.
(5)See Safe Operating Area curves or contact the factory for the appropriate derating.
(6)During solder reflow of SMD package version do not elevate the module case, pins, or internal component tpeemakpeorfa2tu1r5e°sC.aFbovre
a
further guidance refer to the application note, “Reflow Soldering Requirements for Plug-in Power Surface Mount Products,” (SLTA051).
(7)The case pins on the through-hole package types (suffixes
N & A) must be soldered. For more informationacksaegee otuhtelinaepdprliacwabilneg. p
For technical support and more information, see inside back cover or visit www.ti.com