Datasheet > PL663-19

PL663-19

更新时间： 2024-02-27 08:17:24

品牌	Logo	应用领域
PLL		倍频器
页数	文件大小	规格书
15页	484K
描述
Analog Frequency Multiplier

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

PL663-19 技术参数

生命周期：	Active	Reach Compliance Code：	compliant
风险等级：	5.37	安装特点：	SURFACE MOUNT
端子数量：	16	最高工作温度：	85 °C
最低工作温度：	-40 °C	封装主体材料：	PLASTIC/EPOXY
封装等效代码：	LCC16,.12SQ,20	电源：	2.5/3.3 V
子类别：	RF/Microwave Frequency Multipliers	最大压摆率：	75 mA
表面贴装：	YES	技术：	CMOS

PL663-19 数据手册

Analog Frequency Multiplier

PL660 and PL663 XO Families

120 MHz AFM Tuning: Using the “AFM Tuning Assistant” find the PL660-0x in the L2X worksheet. Enter the

Cinternal value found next to it into cell B21. In cell B24 enter the closest standard inductor value (see CoilCraft

0603CS series for example) to achieve the closest peak frequency to 60 MHz. Repeat the same procedure for

L4X at 120 MHz.

Results: L2X = 180 nH, L4X = 82 nH.

320 MHz AFM tuning: Repeat the previous procedure for L2X at 120 MHz and L4X at 320 MHz.

Results: L2X = 24 nH, L4X = 10 nH.

Proceed and assemble the test units.

Measuring 120 MHz L2X: Connect the RF generator and scope probe as shown in Figure 6. While power is

applied to the PCB, set the generator output to +12 dBm and the frequency to 30 MHz. Since this is the 2x port,

the scope will show 60 MHz with ~ 3V pk-pk amplitude. Vary the generator above and below 30 MHz until the

amplitude on the scope is maximum and record the generator frequency. For example peak recorded at 29.8x2 or

59.6 MHz.

Measuring 320 MHz L2X: Connect the RF generator and scope probe as shown in Figure 6. While power is

applied to the PCB, set the generator output to +12 dBm and the frequency to 80 MHz. Since this is the 2x port the

scope will show 160 MHz with ~ 3V pk-pk amplitude. Vary the generator above and below 80 MHz until the

amplitude on the scope is maximum and record the generator frequency. For example peak recorded at 78.0 x 2 =

156 MHz

In the AFM Tuning Assistant, add the scope’s probe capacitance to the Cstray cell. For our example 0.5 pF + 1.0

pF = 1.5 pF. With L2X at 24 nH adjust LWB1 (cell B23) until the peak frequency reads 156 MHz. Next replace the

L2X value with 180 nH and see if it peaks at 59.6 MHz. If it does not, adjust the Cstray until 59.4 MHz is achieved.

Again enter 24 nH for L2X and fine tune LWB1 for 156 MHz.

Results: LWB1 = 1.6 nH, Cstray = 2.9 pF-0.5 pF = 2.4 pF (subtract scope probe stray)

Repeat the same steps for the L4X: Set the generator to 80 MHz. The 82 nH peaks at 118 MHz and the 10 nH

peaks at 304 MHz.

Results: LWB1 = 1.8 nH, Cstray = 2.5 pF-0.5 pF = 2.0 pF (subtract scope probe stray)

Internal Capacitor Selection by Device

Device Number

Cinternal (pF)

PL660-0X

PL663-0X

PL663-1X

PL663-2X

34.125

46.500

14.625

16.500

47745 Fremont Blvd., Fremont, California 94538 TEL (510) 492-0990, FAX (510) 492-0991

www.phaselink.com

Rev. 3/20/07 Page 7

1...4 5 678 9 10...15

下载PDF

与PL663-19相关器件

型号	品牌	描述	获取价格	数据表
PL663-19OI	MICROCHIP	Converter	获取价格
PL663-19OI-R	MICROCHIP	Converter	获取价格
PL663-19QC	MICROCHIP	LVDS Output Clock Oscillator	获取价格
PL663-28	PLL	Analog Frequency Multiplier	获取价格
PL663-28	MICROCHIP	The Analog Frequency Multipliers? (AFMs) are	获取价格
PL663-28OC	MICROCHIP	Converter	获取价格

产品中心

服务支持

精选活动

关于我们

帮助中心

PL663-19

PL663-19 技术参数

PL663-19 数据手册

与PL663-19相关器件

与PL663-19相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

PL663-19

PL663-19 技术参数

PL663-19 数据手册

与PL663-19相关器件

与PL663-19相关文章

您还可以找

您在本页遇到什么问题？