Datasheet > PCF8563TS-4

PCF8563TS-4

更新时间： 2022-12-01 17:34:27

品牌	Logo	应用领域
恩智浦 - NXP		时钟
页数	文件大小	规格书
45页	429K
描述
Real-time clock/calendar

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

PCF8563TS-4 数据手册

PCF8563

NXP Semiconductors

Real-time clock/calendar

7.2 Pin description

Table 3.

Symbol

Pin description

Description

DIP8, SO8, TSSOP8 HVSON10

OSCI

OSCO

INT

oscillator input

oscillator output

5^[1]

interrupt output (open-drain; active LOW)

ground

V_SS

SDA

SCL

serial data input and output

serial clock input

CLKOUT

V_DD

clock output, open-drain

supply voltage

n.c.

3, 10

not connected; do not connect and do not

use as feed through

[1] The die paddle (exposed pad) is wired to V_SSbut should not be electrically connected.

8. Functional description

The PCF8563 contains sixteen 8-bit registers with an auto-incrementing register address,

an on-chip 32.768 kHz oscillator with one integrated capacitor, a frequency divider which

provides the source clock for the Real-Time Clock (RTC) and calender, a programmable

clock output, a timer, an alarm, a voltage-low detector, and a 400 kHz I²C-bus interface.

All 16 registers are designed as addressable 8-bit parallel registers although not all bits

are implemented. The first two registers (memory address 00h and 01h) are used as

control and/or status registers. The memory addresses 02h through 08h are used as

counters for the clock function (seconds up to years counters). Address locations 09h

through 0Ch contain alarm registers which define the conditions for an alarm.

Address 0Dh controls the CLKOUT output frequency. 0Eh and 0Fh are the Timer_control

and Timer registers, respectively.

The Seconds, Minutes, Hours, Days, Months, Years as well as the Minute_alarm,

Hour_alarm, and Day_alarm registers are all coded in Binary Coded Decimal (BCD)

format.

When one of the RTC registers is written or read, the contents of all time counters are

frozen. Therefore, faulty writing or reading of the clock and calendar during a carry

condition is prevented.

8.1 CLKOUT output

A programmable square wave is available at the CLKOUT pin. Operation is controlled by

the register CLKOUT_control at address 0Dh. Frequencies of 32.768 kHz (default),

1.024 kHz, 32 Hz, and 1 Hz can be generated for use as a system clock, microcontroller

clock, input to a charge pump, or for calibration of the oscillator. CLKOUT is an open-drain

output and enabled at power-on. If disabled it becomes high-impedance.

PCF8563

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 9 — 16 June 2011

5 of 45

1 2 3 456 7 8...45

下载PDF

与PCF8563TS-4相关器件

型号	品牌	描述	获取价格	数据表
PCF8563TS5	NXP	Real-time clock/calendar	获取价格
PCF8563TS-5	NXP	Real-time clock/calendar	获取价格
PCF8563TS-T	NXP	Real-time clock/calendar	获取价格
PCF8563T-T	NXP	IC 1 TIMER(S), REAL TIME CLOCK, PDSO8, 3.90 MM, PLASTIC, MS-012, SOT-96-1, SOP-8, Timer or	获取价格
PCF8564A	NXP	Real time clock and calendar	获取价格
PCF8564A_10	NXP	Real time clock and calendar	获取价格