2.0 Hook Up
2.1
Connect the power supply +Out lead to the +In terminal of the Customer
Evaluation Board.
2.2
Connect the power supply –Out lead to the –In terminal of the Customer
Evaluation Board.
2.3
2.4
A high quality, low-noise power supply should be connected to these locations
Connect a lead between the +Out of the Customer Evaluation Board and +In
of the load.
2.5
2.6
Connect a lead between the –Out of the Customer Evaluation Board and –In
of the load.
Connections to these locations should be with short heavy gauge leads.
3.0 Verify Connections
4.0 Test Sequence
4.1
4.2
4.3
4.4
4.5
Have the latest version of the PRM® data sheet in hand.
Assure that the DC supply is set to 0 Vdc prior to turning the unit on.
Confirm that the switch bank is configured as shown in the silk screen on the board.
Turn on the DC supply.
Make sure the DC load is set to constant current and at 0 A prior to turning
on the load.
4.6
4.7
Turn on the DC load.
Connect an oscilloscope to the test point provided to monitor output voltage. Many
types of scope probes may be directly connected to these points if the probe is
equipped with a removable plastic sheath. Be careful to avoid creating ground loops
when making measurements of this voltage and the input voltage. It is recommended
that the measurements be made separately. Shorting the -input and -output of the PRM
will defeat the PRM current limit feature as the current shunt is in this path.
Turn on a fan if desired.
4.8
4.9
4.10
Raise the DC input voltage to the nominal value indicated on the data sheet.
Verify no load operation by raising and lowering the input voltage through the entire
input voltage range. The output voltage should remain constant within the tolerance
indicated in the data sheet.
4.11
4.12
Re-establish the nominal input voltage.
Slowly increase the load current to full load while monitoring the output voltage. The
output voltage should remain within the limits specified in the appropriate PRM data
sheet.
4.13
4.14
Return the load current to 0 A and decrease the input voltage to low line.
Repeat step 4.12. Depending upon the supply used and the source impedance it may
be necessary to adjust the input voltage to keep the input to the PRM at low line.
Return the load current to 0 A and increase the input voltage to high line.
Repeat step 4.12.
4.15
4.16
5.0 You have now verified the functionality of the PRM over the entire line and load
operating range.
6.0 Deviating from Nominal Settings
This board has provisions, as described in the Board Overview section, to adjust the
configuration of the PRM about the nominal values. The data sheet for the PRM has equations
and curves for determining the required resistor values needed for specific conditions.
Applications requiring output voltages other than the nominal setting will need to have the
new value set via the trim pots and respective switches. Reference Items 4 and 5 of the Board
Overview and the schematic shown in Figure 2.
6.1
Adjust the PRM Output Voltage Set Point
6.1.1 Make sure that the power is removed from the unit prior to making adjustment.
6.1.2 Using a DMM (set to measure resistance), probe between SG (Item 3) and the pad
labeled OS located next to the 5 kΩ trim pot R08.
UG:003
vicorpower.com
Applications Engineering: 800 927.9474
Page 5
5秒后页面跳转
资料手册解读：UC3842参数和管脚说明
一文带你了解无源晶振的负载电容为何要加两颗谐振电容CL1和CL2
玻璃管保险丝与陶瓷管保险丝：区别与替代性探讨
PCF8574资料解读：主要参数分析、引脚说明
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
