OLED-100H016A-LPP3N00000
www.vishay.com
Vishay
INSPECTION SPECIFICATION
NO.
ITEM
CRITERION
AQL
8.1 Illumination source flickers when lit
0.65
8.2 Spots or scratched that appear when lit must be judged. Using OLED spot, lines and
contamination standards
08
Backlight elements
2.5
8.3 Backlight does not light or color wrong
0.65
2.5
9.1 Bezel may not have rust, be deformed or have fingerprints, stains or other contamination
9.2 Bezel must comply with job specifications
09
10
Bezel
0.65
2.5
10.1 COB seal may not have pinholes larger than 0.2 mm or contamination
10.2 COB seal surface may not have pinholes through to the IC
10.3 The height of the COB should not exceed the height indicated in the assembly diagram
2.5
0.65
10.4 There may not be more than 2 mm of sealant outside the seal area on the PCB. And there
should be no more than three places
2.5
2.5
PCB, COB
10.5 No oxidation or contamination PCB terminals
10.6 Parts on PCB must be the same as on the production characteristic chart. There should be
no wrong parts, missing parts or excess parts
0.65
0.65
2.5
10.7 The jumper on the PCB should conform to the product characteristic chart
10.8 If solder gets on bezel tab pads, OLED pad, zebra pad or screw hold pad, make sure it is
smoothed down
11.1 No un-melted solder paste may be present on the PCB
11.2 No cold solder joints, missing solder connections, oxidation or icicle
11.3 No residue or solder balls on PCB
2.5
2.5
11
Soldering
2.5
11.4 No short circuits in components on PCB
0.65
2.5
12.1 No oxidation, contamination, curves or, bends on interface pin (OLB) of TCP
12.2 No cracks on interface pin (OLB) of TCP
0.65
2.5
12.3 No contamination, solder residue or solder balls on product
12.4 The IC on the TCP may not be damaged, circuits
2.5
12.5 The uppermost edge of the protective strip on the interface pin must be present or look as
if it cause the interface pin to sever
2.5
2.5
12
General appearance
12.6 The residual rosin or tin oil of soldering (component or chip component) is not burned into
brown or black color
12.7 Sealant on top of the ITO circuit has not hardened
2.5
12.8 Pin type must match type in specification sheet
0.65
0.65
0.65
0.65
12.9 OLED pin loose or missing pins
12.10 Product packaging must the same as specified on packaging specification sheet
12.11 Product dimension and structure must conform to product specification sheet
Revision: 14-Aug-17
Document Number: 37973
9
For technical questions, contact: displays@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
