MPM3690-50A/B – 16V, DUAL 25A OR SINGLE 50A POWER MODULE
PIN FUNCTIONS
Pin Number
Name
Description
A1–A5, B1–B5, C1–
VOUT1
GND
Power output 1. Power output pins for channel 1.
C4
A6, A7, B6, B7, D1–
D4, D9–D12, E1–E4,
E10, E11, E12, F1,
F2, F3, F6, F7, F10,
F11, F12, G1, G3,
G7, G10, G12, H1–
H7, H9–H12, J1, J5,
J8, J12, K1, K5–K8,
K12, L1, L12, M1,
M12
Power ground. GND is the ground of the regulated output voltage (VOUT).
A8–A12, B8–B12,
C9–C12
VOUT2
Power output 2. Power output pins for channel 2.
VS1P,
VS2P
Positive input of the remote-sense amplifier. Connect these pins to the
VOUT remote sense point.
C5, C8
Negative input of the remote-sense amplifier. Connect these pins to the
output GND remote sense point to enable remote sense. Connect directly
to GND to disable the remote sense function.
VS1N,
VS2N
D6, C7
Frequency set. Connect a resistor between these pins and AGND to
configure the switching frequency (fSW) between 400kHz to 1MHz. For the
MPM3690-50B, the FSET1 and FSET2 resistors must be the same.
FSET1,
FSET2
C6, E7
Feedback voltage. Connect a resistor to these pins between VS1N and
D5, D7
E5, D8
G5, G4
FB1, FB2 VS2N to configure VOUT. This pin is connected to VS1P and VS2P with a
60.4kΩ resistor.
Soft-start time setting. Connect a ceramic capacitor to set the soft-start
SS1, SS2
time (tSS).
Ramp selection pin. Float these pins to set the internal compensation
ramp to high; pull these pins pin low to set the internal compensation ramp
to low.
RAMP1,
RAMP2
E8, F8
F4
VSOUT
MODE
Not connected (internally floated). Float these pins.
Operation mode set. Pull MODE up to VCC for forced continuous
conduction mode (FCCM).
Enable pins. Drive EN pin high to turn the output on, drive it low to turn the
output off. Do not float this pin.
F5, F9
G2, G11
G6
EN1, EN2
SW1, SW2 Switching nodes. Float these pins.
Protection mode selection. Connect PMODE to GND for latch-off mode,
pull PMODE up to VCC for hiccup mode.
PMODE
PG1, PG2
VCC
Power good outputs. The output of the PG pins is an open drain. Pull the
PG pins high with a pull-up resistor.
G9, G8
H8
Output of the internal power supply. Float this pin or connect it to an
external 3.3V power supply to improve efficiency.
NC1, NC2,
NC3, NC4
E6, J6, J7, E9
Not connected (internally floated). Float these pins.
M2–M11, L2–L11, J2,
J3, J4, J9, J10, J11,
K2, K3, K4, K9, K10,
K11
VIN
Supply voltage. Connect input voltage between these pins and GND pins.
MPM3690-50 Rev. 1.0
MonolithicPower.com
4
5/24/2021
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2021 MPS. All Rights Reserved.