5秒后页面跳转
MCP23S09 PDF预览

MCP23S09

更新时间: 2024-02-21 03:59:33
品牌 Logo 应用领域
美国微芯 - MICROCHIP /
页数 文件大小 规格书
50页 605K
描述
8-Bit I/O Expander with Open-Drain Outputs

MCP23S09 技术参数

是否无铅: 不含铅是否Rohs认证: 符合
生命周期:Active零件包装代码:SSOP
包装说明:5.30 MM, LEAD FREE, PLASTIC, SSOP-20针数:20
Reach Compliance Code:compliantECCN代码:EAR99
HTS代码:8542.39.00.01风险等级:5.51
JESD-30 代码:R-PDSO-G20JESD-609代码:e3
长度:7.2 mm湿度敏感等级:1
I/O 线路数量:8端口数量:1
端子数量:20最高工作温度:125 °C
最低工作温度:-40 °C封装主体材料:PLASTIC/EPOXY
封装代码:SSOP封装形状:RECTANGULAR
封装形式:SMALL OUTLINE, SHRINK PITCH峰值回流温度(摄氏度):260
认证状态:Not Qualified座面最大高度:2 mm
最大供电电压:5.5 V最小供电电压:1.8 V
标称供电电压:5 V表面贴装:YES
技术:CMOS温度等级:AUTOMOTIVE
端子面层:MATTE TIN (SN)端子形式:GULL WING
端子节距:0.65 mm端子位置:DUAL
处于峰值回流温度下的最长时间:40宽度:5.3 mm
uPs/uCs/外围集成电路类型:PARALLEL IO PORT, GENERAL PURPOSE

MCP23S09 数据手册

 浏览型号MCP23S09的Datasheet PDF文件第1页浏览型号MCP23S09的Datasheet PDF文件第2页浏览型号MCP23S09的Datasheet PDF文件第4页浏览型号MCP23S09的Datasheet PDF文件第5页浏览型号MCP23S09的Datasheet PDF文件第6页浏览型号MCP23S09的Datasheet PDF文件第7页 
MCP23009/MCP23S09  
1.0  
DEVICE OVERVIEW  
The MCP23X09 device provides 8-bit, general purpose  
parallel I/O expansion for I2C bus or SPI applications.  
The two devices differ only in the serial interface.  
• MCP23009 - I2C interface  
• MCP23S09 - SPI interface  
The MCP23X09 consists of multiple 8-bit configuration  
registers for input, output and polarity selection. The  
system master can enable the I/Os as either inputs or  
outputs by writing the I/O configuration bits. The data  
for each input or output is kept in the corresponding  
input or output register. The polarity of the input port  
register can be inverted with the polarity inversion  
register. All registers can be read by the system master.  
The interrupt output can be configured to activate  
under two conditions (mutually exclusive):  
1. When any input state differs from its  
corresponding input port register state. This is  
used to indicate to the system master that an  
input state has changed.  
2. When an input state differs from  
a
pre-configured  
register).  
register  
value  
(DEFVAL  
The Interrupt Capture register captures port values at  
the time of the interrupt, thereby saving the condition  
that caused the interrupt.  
The Power-on Reset (POR) sets the registers to their  
default values and initializes the device state machine.  
The hardware address pin is used to determine the  
device address.  
© 2009 Microchip Technology Inc.  
DS22121B-page 3  

与MCP23S09相关器件

型号 品牌 描述 获取价格 数据表
MCP23S09-E/MG MICROCHIP 8 I/O, PIA-GENERAL PURPOSE, PQCC16, 3 X 3 MM, 0.90 MM HEIGHT, PLASTIC, QFN-16

获取价格

MCP23S09-E/P MICROCHIP 8-Bit I/O Expander with Open-Drain Outputs

获取价格

MCP23S09-E/SO MICROCHIP 8-Bit I/O Expander with Open-Drain Outputs

获取价格

MCP23S09-E/SS MICROCHIP 8-Bit I/O Expander with Open-Drain Outputs

获取价格

MCP23S09EMG MICROCHIP 8-Bit I/O Expander with Open-Drain Outputs

获取价格

MCP23S09EP MICROCHIP 8-Bit I/O Expander with Open-Drain Outputs

获取价格