5秒后页面跳转
MC13142 PDF预览

MC13142

更新时间: 2024-02-23 17:09:21
品牌 Logo 应用领域
摩托罗拉 - MOTOROLA 放大器
页数 文件大小 规格书
16页 165K
描述
LOW POWER DC - 1.8 GHz LNA, MIXER and VCO

MC13142 技术参数

生命周期:Obsolete零件包装代码:QFP
包装说明:LQFP,针数:20
Reach Compliance Code:unknownHTS代码:8542.39.00.01
风险等级:5.84JESD-30 代码:S-PQFP-G20
长度:4 mm功能数量:1
端子数量:20最高工作温度:85 °C
最低工作温度:-40 °C封装主体材料:PLASTIC/EPOXY
封装代码:LQFP封装形状:SQUARE
封装形式:FLATPACK, LOW PROFILE认证状态:Not Qualified
座面最大高度:1.6 mm标称供电电压:3 V
表面贴装:YES电信集成电路类型:RF AND BASEBAND CIRCUIT
温度等级:INDUSTRIAL端子形式:GULL WING
端子节距:0.65 mm端子位置:QUAD
宽度:4 mm

MC13142 数据手册

 浏览型号MC13142的Datasheet PDF文件第1页浏览型号MC13142的Datasheet PDF文件第2页浏览型号MC13142的Datasheet PDF文件第3页浏览型号MC13142的Datasheet PDF文件第5页浏览型号MC13142的Datasheet PDF文件第6页浏览型号MC13142的Datasheet PDF文件第7页 
MC13142  
PIN FUNCTION DESCRIPTION  
Pin  
16 Pin  
SOIC  
Equivalent Internal Circuit  
(20 Pin LQFP)  
Symbol  
EN  
Description  
1
Enable, E Osc  
V
CC  
In SO–16, both enables, (for the Oscillator/LO Buffer and  
LNA/Mixer) are bonded to Pin 1. Enable by pulling up to  
1
40 k  
2.0 V  
V
CC  
or to greater than 2.0 V  
.
BE  
EN  
BE  
V
CC  
70 k  
2.0 V  
BE  
2
3
RF  
RF Input  
V
in  
CC  
The input is the base of an NPN low noise amplifier.  
Minimum external matching is required to optimize the  
input return loss and gain.  
600  
16  
RF  
V
ref2  
out  
V
EE  
V
– Negative Supply  
pin is taken to an ample dc ground plane through a  
EE  
V
EE  
low impedance path. The path should be kept as short  
as possible. A two sided PCB is implemented so that  
ground returns can be easily made through via holes.  
V
EE  
V
ref3  
2
RF  
in  
3
16  
RF  
out  
RF Output  
2.0 mA  
The output is from the collector of the LNA; it is internally  
biased with a 600 resistor to V . As shown in the 926  
MHz application receiver the output is conjugately  
matched with a shunt L, and series L and C network.  
V
CC  
EE  
4
5
6
Osc E  
Osc B  
Osc C  
On–Board VCO Transistor  
The transistor has the emitter, base and collector + V  
pins available. Internal biasing which is compensated for  
stability over temperature is provided. It is recommended  
4
CC  
Osc E  
10  
that the base pin is pulled up to V  
through an RFC  
5
CC  
chosen for the particular oscillator center frequency. The  
application circuit shows a modified Colpitts or Clapp  
oscillator configuration and its design is discussed in  
detail in the application section.  
1.5  
mA  
Osc B  
7.6 k  
6
V
EE  
Osc C  
6
8
V
CC  
V
CC  
Supply Voltage (V  
)
CC  
pins are provided for the Local Oscillator and  
Two V  
V
V
CC  
LO Buffer Amplifier. The operating supply voltage range  
EE  
6
is from 2.7 Vdc to 6.5 Vdc. In the PCB layout, the V  
trace must be kept as wide as feasible to minimize  
CC  
V
CC  
inductive reactances along the trace. V  
should be  
CC  
at the IC pin as shown in the  
component placement view.  
CC  
decoupled to V  
EE  
7
LO Buf  
7
LO Buff  
Local Oscillator Buffer  
1.0  
mA  
This is a buffered output providing –16 dBm  
8
(50 termination) to drive the f pin of a PLL  
in  
synthesizer. Impedance matching to the synthesizer may  
be necessary to deliver the optimal signal and to  
improve the phase noise performance of the VCO.  
V
CC  
V
EE  
4
MOTOROLA RF/IF DEVICE DATA  

与MC13142相关器件

型号 品牌 描述 获取价格 数据表
MC13142D MOTOROLA LOW POWER DC - 1.8 GHz LNA, MIXER and VCO

获取价格

MC13142DR2 MOTOROLA TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, PDSO16, PLASTIC, SO-16

获取价格

MC13142FTB MOTOROLA TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, PQFP20, TQFP-20

获取价格

MC13143 MOTOROLA ULTRA LOW POWER DC - 2.4 GHz LINEAR MIXER

获取价格

MC13143D MOTOROLA ULTRA LOW POWER DC - 2.4 GHz LINEAR MIXER

获取价格

MC13144 MOTOROLA VHF - 2.0 GHz LOW NOISE AMPLIFIER WITH PROGRAMMABLE BIAS

获取价格