www.micropowerdirect.com
EMC Specifications
Notes:
Parameter
Standard
See Note 1
1. All units are rated for EN 55022 (CE/RE) class A without external components.
They will meet class B with the addition of the MDCFM-02A(W) (or a similar
discrete filter circuit). Contact the factory for more information.
2. To meet the requirements of EN 61000-4-4 ( 2 kV), external components
are needed.This can be done discretely, or with the addition of the MDCFM-
02A(W). Contact the factory for more information.
Radiated Emissions
EN 55022
EN 55022
Class A
Class A
Conducted Emissions
See Note 1
ESD
RS
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-29
Criteria B; 4 kV Contact
Criteria A; 10V/m
3. To meet the requirements of EN 61000-4-5 ( 2 kV), external components are
needed.This can be done discretely, or with the addition of the MDCFM-02(W).
Contact the factory for more information.
EFT
Surge
CS
See Note 2
See Note 3
Criteria B; 2 kV
Criteria B; 2 kV
Criteria A; 3 Vrms
Criteria B; 0% - 70%
Voltage Dips
Typical Connection
5. Recommended values for components are:
7. In many applications simply adding input/output capacitors will
enhance the input surge pro-
The diagram above illustrates a typical connection of the MB1500ERU
series for applications that require meeting EMC standards.The units do not
require external components to operate as specified. Some notes on this
diagram (starting with the input circuit) are:
1. It is recommended that an external fuse be used.The recommended fuse
is shown in the model chart on page 2.
2. An external MOV is recommended on the input to protect the unit in the
event of a surge. A recommended value is given in the table at right.
3. An external TVS is recommended on the input to protect the unit in the
event of a voltage spike. A recommended value is given in the table at
right.
4. The output filtering capacitor (C3) is a high frequency, low resistance
electrolytic capacitor. Care must be taken in choosing this capacitor not
to exceed the capacitive load specification for the unit. The board layout
illustrationbelowshowsaconnectionfordualoutputunits.Voltagederating
of capacitors should be 80% or above.
Component
24 VIN
S14K35
48 VIN
S14K60
Vin
Input
Vout
Output
tection and reduce output
ripple sufficiently. The input
capacitor C1 and output cap-
acitors C3 and C4 shown in the
typical connection diagram
above (and board layout
MOV
L1
(VDC) Capacitor (VDC) Capacitor
56 µH
56 µH
3.3
5.0
12
15
24
5
470 µF
470 µF
220 µF
220 µF
100 µF
220 µF
100 µF
100 µF
24
48
330 µF
330 µF
TVS
C1
C2
SMCJ48A
330 µF/50V
1.0 µF/50V
4.7 µH
SMCJ90A
330 µF/100V
1.0 µF/100V
4.7 µH
drawings below) illustrate
L2
their connection. Recommended capacitor
values are given in the table at right.
CY1, CY2
1,000 pF/2 kV
1,000 pF/2 kV
12
15
6. Input noise and surge suppression modules are available for a
number of MPD DC/DC power supplies.For pricing or full techni-
cal information on these modules please contact the factory.
Typical Board Layout: With External Filter/Surge Components for Single Output Unit
Typical Connection: With External Filter/Surge Components for Dual Output Unit
MicroPower Direct
• 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com