2.4W, Single-Supply, Class G Power Amplifier
MAX9730
ELECTRICAL CHARACTERISTICS (continued)
(V
= V
= V
= 3.6V, V
= V
= 0V, R
= R = 10kΩ, R
= R
= 10kΩ, R = 100kΩ, C1 = 4.7µF, C2 =
FB-
FS
IN+
IN-
FB+
CC
CPVDD
SHDN
GND
CPGND
10µF; speaker load resistors (R ) are terminated between OUT+ and OUT-, unless otherwise stated; T = T
to T
, unless other-
MAX
L
A
MIN
wise noted. Typical values are at T = +25°C.) (Notes 1, 2)
A
PARAMETER
Voltage Gain
SYMBOL
CONDITIONS
MIN
TYP
12
MAX
UNITS
A
(Notes 4, 7)
11.5
12.5
dB
V
V
V
V
V
V
V
V
V
V
= 5V
2.4
1.67
1.25
0.8
7.1
5.9
5.1
4.2
6.5
CC
CC
CC
CC
CC
CC
CC
CC
CC
= 4.2V
= 3.6V
= 3.0V
= 5V
THD+N = 1%, f = 1kHz,
R = 8Ω
L
Continuous Output Power
P
V
W
OUT
= 4.2V
= 3.6V
= 3.0V
= 5V
f = 1kHz, 1% THD+N,
Z = 1µF + 10Ω
L
Output Voltage
V
RMS
OUT
V
V
V
= 4.2V
= 3.6V
= 3.0V
5.4
4.7
3.8
77
CC
CC
CC
f = 10kHz, 1% THD+N,
Z = 1µF + 10Ω
L
V
= 2.7V to 5.5V
63
CC
f = 217Hz, 200mV
ripple
77
P-P
Power-Supply Rejection Ratio
(Note 4)
PSRR
dB
f = 1kHz, 200mV
ripple
77
58
P-P
f = 20kHz, 200mV
ripple
P-P
R = 8Ω, V
= 1kHz / 400mV
RMS
0.007
0.12
L
OUT
Total Harmonic Distortion Plus
Noise
THD+N
SNR
%
R = 8Ω, V
= 1kHz / 1V
RMS
L
OUT
V
= 0.5V
, inputs to GND by C1N,
OUT
RMS
Signal-to-Noise Ratio
Dynamic Range
95
dB
dB
A-weighted
22Hz to 22kHz
A-weighted
96
99
DR
(Note 9)
Note 1: All devices are 100% production tested at room temperature. All temperature limits are guaranteed by design.
Note 2: Testing performed with resistive and inductive loads to simulate an actual speaker load. For dynamic speakers,
R = 8Ω, 68µH.
L
Note 3: Designed for 1.8V logic.
Note 4:
Note 5: Amplifier inputs AC-coupled to GND.
Note 6: Testing performed at room temperature with 8Ω resistive load in series with 68µH inductive load connected across BTL
output for speaker amplifier. Mode transitions are controlled by SHDN. V is the peak output transient expressed in dBV.
R
IN_
and R
have 0.5% tolerance.
FB_
CP
Note 7: Voltage gain is defined as: [V
- V
] / [V - V ].
IN+ IN-
OUT+
OUT-
Note 8: Mode A tone burst tested at full amplitude for one cycle and half amplitude for nine cycles. Mode B tone burst tested at
full amplitude for three cycles and half amplitude for seven cycles. Full amplitude is defined as 1% THD+N at full battery
(V
= 4.2V). Electrical Characteristics table targets must be met at THD+N = 1% for one cycle (Mode A) and THD+N <
CC
5% for three cycles (Mode B).
Note 9: Dynamic range is calculated by measuring the RMS voltage difference between a -60dBFS output signal and the noise
floor, then adding 60dB. Full scale is defined as the output signal needed to achieve 1% THD+N.
_______________________________________________________________________________________
3