Low -Dropout, 300m A Line a r Re gula tors in SOT23
0.8A (typ). This current limit is reduced to 500mA (typ)
when the output voltage is below 93% of the nominal
value to provide foldback current limiting.
De t a ile d De s c rip t io n
The MAX8887/MAX8888 are low-dropout, low-quies-
cent-current linear regulators designed primarily for
b a tte ry-p owe re d a p p lic a tions . The d e vic e s s up p ly
loads up to 300mA and are available in several fixed
outp ut volta g e s in the 1.5V to 3.3V ra ng e . The
MAX8887 is optimized for low-noise operation, while
the MAX8888 includes an open-drain POK output flag.
As illustrated in Figure 1, the MAX8888 consists of a
1.25V reference, error amplifier, P-channel pass tran-
sistor, and internal feedback voltage divider.
Th e rm a l Ove rlo a d P ro t e c t io n
Thermal overload protection limits total power dissipa-
tion in the MAX8887/MAX8888. When the junction tem-
perature exceeds T =+170°C, a thermal sensor turns
J
off the pass transistor, allowing the device to cool. The
thermal sensor turns the pass transistor on again after
the junction temperature cools by 20°C, resulting in a
pulsed output during continuous thermal overload con-
d itions . The rma l ove rloa d p rote c tion p rote c ts the
MAX8887/MAX8888 in the event of fault conditions. For
continuous operation, do not exceed the absolute maxi-
In t e rn a l P -Ch a n n e l P a s s Tra n s is t o r
The MAX8887/MAX8888 fe a ture a 0.5Ω P-c ha nne l
MOSFET pass transistor. Unlike similar designs using
PNP pass transistors, P-channel MOSFETs require no
base drive, which reduces quiescent current. PNP-
based regulators also waste considerable current in
dropout when the pass transistor saturates and use
hig h b a s e d rive c urre nts und e r la rg e loa d s . The
MAX8887/MAX8888 do not suffer from these problems
and consume only 55µA of quiescent current under
heavy loads as well as in dropout.
mum junction-temperature rating of T =+150°C.
J
Op e ra t in g Re g io n a n d P o w e r Dis s ip a t io n
The MAX8887/MAX8888’s maximum power dissipation
depends on the thermal resistance of the IC package
and circuit board. The temperature difference between
the die junction and ambient air, and the rate of air flow.
✕
The power dissipated in the device is P = I
(V -
IN
OUT
V ). The ma ximum a llowe d p owe r d is s ip a tion is
OUT
727mW or:
Ou t p u t Vo lt a g e S e le c t io n
The MAX8887/MAX8888 are supplied with various fac-
tory-set output voltages ranging from 1.5V to 3.3V. The
part number’s two-digit suffix identifies the nominal out-
put voltage. For example, the MAX8887EZK33 has a
preset output voltage of 3.3V (see the Ordering Infor-
mation).
P
= (T
- T ) / (θ + θ
)
MAX
J(MAX) A JC CA
whe re T
-T is the te mp e ra ture d iffe re nc e
A
J (MAX)
between the MAX8887/MAX8888 die junction and the
surrounding air; θ is the thermal resistance from the
JC
junction to the case; and θ
is the thermal resistance
CA
from the case through PC board, copper traces, and
other materials to the surrounding air.
S h u t d o w n
Drive SHDN low to enter shutdown. During shutdown,
the output is disconnected from the input and supply
current drops to 0.1µA. When in shutdown, POK and
OUT are driven low. SHDN can be pulled as high as
6V, regardless of the input and output voltages.
Refer to Figure 2 for the MAX8887/MAX888 valid oper-
ating region.
No is e Re d u c t io n
For the MAX8887 only, a n e xte rna l 0.01µF b yp a s s
capacitor at BP creates a lowpass filter for noise reduc-
tion. The MAX8887 exhibits 42µV
of output voltage
= 2.2µF (see the
RMS
= 0.01µF and C
OUT
P o w e r-OK Ou t p u t
The power-OK output (POK) pulls low when OUT is less
than 93% of the nominal regulation voltage. Once OUT
exceeds 93% of the nominal voltage, POK goes high
impedance. POK is an open-drain N-channel output.
To obtain a logic level output, connect a pullup resistor
from POK to OUT. A 100kΩ resistor works well for most
applications. POK can be used as a power-on-reset
(POR) signal to a microcontroller (µC) or to drive other
logic. Adding a capacitor from POK to ground creates
POK delay. When the MAX8887 is shut down, POK is
held low independent of the output voltage. If unused,
leave POK grounded or unconnected.
noise with C
BP
Typical Operating Characteristics).
Ap p lic a t io n s In fo rm a t io n
Ca p a c it o r S e le c t io n a n d Re g u la t o r
S t a b ilit y
Connect a 2.2µF ceramic capacitor between IN and
ground and a 2.2µF ceramic capacitor between OUT
a nd g round . The inp ut c a p a c itor (C ) lowe rs the
IN
source impedance of the input supply. Reduce noise
and improve load-transient response, stability, and
power-supply rejection by using a larger ceramic out-
put capacitor such as 4.7µF.
Cu rre n t Lim it
The MAX8887/MAX8888 monitor and control the pass
transistor’s gate voltage, limiting the output current to
The output capacitor’s (C
) equivalent series resis-
OUT
tance (ESR) affects stability and output noise. Use out-
6
_______________________________________________________________________________________
5秒后页面跳转
深入解析CS8416引脚说明、参数、技术特点
TPA3116D2功放芯片参数详解、引脚说明
移位寄存器74HC165引脚说明、驱动程序示例解读
深入解析AD9833：DDS频率合成器的卓越性能与广泛应用
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
替代型号
如果您发现信息不准确，
